Seite 1 von 2
LED blinken lediglich
Verfasst: 14. Apr 2016, 19:45
von chrisT2k
Hallo zusammen,
ich habe die letzten beiden Tage damit beschäftigt, die LED Stripes zusammen zu löten. Mit einem Spannungsprüfer habe ich lediglich feststellen können, dass die LED von hinten bis vorne mit Strom versorgt werden.
Heute habe ich dann den Stripe mit dem RasPi und dem Netzteil verbunden und alles so gemacht, wie in der Anleitung Teil 2 beschrieben war.
Jedoch habe ich das Problem, dass bei mir lediglich die ersten vier LED blinken und eine weitere LED (wenn sie denn Lust hat) auf Platz 70 um den Dreh. Jedoch blinken die LED immer, wenn der Stripe am Netzteil hängt. Der Kontakt mit dem RasPi scheint den Stripe nicht zu interessieren (Löse ich die Verbindung zum RasPi, blinken die LED nämlich im gleichen Rythmus weiter).
Ich habe also die Lötstellen am GPIO-Port angeschaut und auch hier mal den Spannungsmesser ran gehalten. Dort bekomme ich von jedem Kontakt einen Impuls in den Stecker hinein. Auch sind die Kabel an den Ports angeschlossen, wie sie auch in der Anleitung eingezeichnet waren.
Nun weiß ich nicht mehr weiter, woran das ständige Blinken liegen könnte.
Hat jemand von euch da vielleicht eine Ahnung bzw. den ein oder anderen Tipp?
Viele Grüße,
chrisT2k
LED blinken lediglich
Verfasst: 14. Apr 2016, 20:06
von Avalox2k
Beitrag 1 abarbeiten, sonst raten wir Weihnachten noch, woran es liegt
viewtopic.php?p=5307#p5307Getippt mit meinem Galaxy S6 Edge+ mit Tapatalk
LED blinken lediglich
Verfasst: 15. Apr 2016, 00:53
von chrisT2k
Hab den dann mal weitestgehend abgearbeitet
1. Ich habe die WS2801 auf AliExpress bestellt, den genauen Link finde ich jedoch nicht mehr
2. die Bilder werde ich in den nachfolgenden Posts online stellen
3.
Code: Alles auswählen
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
disable_overscan=0
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# comment to get jack audio
hdmi_drive=2
config_hdmi_boost=0
hdmi_force_hotplug=0
# uncomment for composite PAL
#sdtv_mode=2
# uncomment for lirc-rpi
#dtoverlay=lirc-rpi
# Overclock
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=512
avoid_safe_mode=1
kernel=zImage
# NOOBS Auto-generated Settings:
hdmi_force_hotplug=1
config_hdmi_boost=4
overscan_left=24
overscan_right=24
overscan_top=16
overscan_bottom=16
disable_overscan=0
arm_freq=1050
core_freq=500
sdram_freq=500
force_turbo=0
over_voltage=6
over_voltage_sdram=0
gpu_freq=250
overscan_scale=1
# Ambilight Modul
dtparam=spi=on
4.
Code: Alles auswählen
// Automatically generated configuration file for 'Hyperion daemon'
// Generated by: HyperCon (The Hyperion deamon configuration file builder)
// Created with HyperCon V1.01.2 (31.03.2016)
{
/// Device configuration contains the following fields:
/// * 'name' : The user friendly name of the device (only used for display purposes)
/// * 'type' : The type of the device or leds (known types for now are
/// ---------SPI---------, APA102, WS2801, P9813, LPD6803, LPD8806, ---------PWM---------, WS2812b (just RPi1), WS281X (RPi1, RPi2, RPi3), --------OTHER--------, PhilipsHUE, AtmoOrb, PiBlaster, Tinkerforge, UDP, FadeCandy, SEDU, TPM2, USBASP-WS2801, USBASP-WS2812, ------3rd PARTY------, Adalight, AdalightAPA102, AmbiLed, Atmo, Lightpack, Multi-Lightpack, Paintpack, Test (file), None)
/// * [device type specific configuration]
/// * 'colorOrder' : The order of the color bytes ('rgb', 'rbg', 'bgr', etc.).
"device" :
{
"name" : "MyHyperionConfig",
"type" : "ws2801",
"output" : "/dev/spidev0.0",
"rate" : 250000,
"colorOrder" : "rgb"
},
/// Color manipulation configuration used to tune the output colors to specific surroundings.
/// The configuration contains a list of color-transforms. Each transform contains the
/// following fields:
/// * 'id' : The unique identifier of the color transformation (eg 'device_1') /// * 'leds' : The indices (or index ranges) of the leds to which this color transform applies
/// (eg '0-5, 9, 11, 12-17'). The indices are zero based. /// * 'hsv' : The manipulation in the Hue-Saturation-Value color domain with the following
/// tuning parameters:
/// - 'saturationGain' The gain adjustement of the saturation
/// - 'valueGain' The gain adjustement of the value
/// * 'red'/'green'/'blue' : The manipulation in the Red-Green-Blue color domain with the
/// following tuning parameters for each channel:
/// - 'threshold' The minimum required input value for the channel to be on
/// (else zero)
/// - 'gamma' The gamma-curve correction factor
/// - 'blacklevel' The lowest possible value (when the channel is black)
/// - 'whitelevel' The highest possible value (when the channel is white)
///
/// Next to the list with color transforms there is also a smoothing option.
/// * 'smoothing' : Smoothing of the colors in the time-domain with the following tuning
/// parameters:
/// - 'type' The type of smoothing algorithm ('linear' or 'none')
/// - 'time_ms' The time constant for smoothing algorithm in milliseconds
/// - 'updateFrequency' The update frequency of the leds in Hz
/// - 'updateDelay' The delay of the output to leds (in periods of smoothing)
"color" :
{
"correction" :
[
{
"id" : "default",
"leds" : "*",
"correctionValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"temperature" :
[
{
"id" : "default",
"leds" : "*",
"temperatureValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"transform" :
[
{
"id" : "default",
"leds" : "*",
"hsv" :
{
"saturationGain" : 1.0000,
"valueGain" : 1.0000
},
"hsl" :
{
"saturationGain" : 1.0000,
"luminanceGain" : 1.0000
},
"red" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"green" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"blue" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
}
}
],
"smoothing" :
{
"type" : "linear",
"time_ms" : 100,
"updateFrequency" : 25.0000,
"updateDelay" : 0
}
},
/// The black border configuration, contains the following items:
/// * enable : true if the detector should be activated
/// * threshold : Value below which a pixel is regarded as black (value between 0.0 and 1.0)
/// * unknownFrameCnt : Number of frames without any detection before the border is set to 0 (default 600)
/// * borderFrameCnt : Number of frames before a consistent detected border gets set (default 50)
/// * maxInconsistentCnt : Number of inconsistent frames that are ignored before a new border gets a chance to proof consistency
/// * blurRemoveCnt : Number of pixels that get removed from the detected border to cut away blur (default 1)
/// * mode : Border detection mode (values=default,classic,osd)
"blackborderdetector" :
{
"enable" : true,
"threshold" : 0.01,
"unknownFrameCnt" : 600,
"borderFrameCnt" : 50,
"maxInconsistentCnt" : 10,
"blurRemoveCnt" : 1,
"mode" : "default"
},
/// The configuration of the effect engine, contains the following items:
/// * paths : An array with absolute location(s) of directories with effects
/// * color : Set static color after boot -> set effect to "" (empty) and input the values [R,G,B] and set duration_ms NOT to 0 (use 1) instead
/// * effect : The effect selected as 'boot sequence'
/// * duration_ms : The duration of the selected effect (0=endless)
/// * priority : The priority of the selected effect/static color (default=990) HINT: lower value result in HIGHER priority!
"effects" :
{
"paths" :
[
"/storage/hyperion/effects"
]
},
"bootsequence" :
{
"color" : [0,0,0],
"effect" : "Rainbow swirl fast",
"duration_ms" : 3000,
"priority" : 990
},
/// The configuration of the Json/Proto forwarder. Forward messages to multiple instances of Hyperion on same and/or other hosts
/// 'proto' is mostly used for video streams and 'json' for effects
/// * proto : Proto server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19447"] or more instances to forward ["127.0.0.1:19447","192.168.0.24:19449"]
/// * json : Json server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19446"] or more instances to forward ["127.0.0.1:19446","192.168.0.24:19448"]
/// HINT: If you redirect to "127.0.0.1" (localhost) you could start a second hyperion with another device/led config!
/// Be sure your client(s) is/are listening on the configured ports. The second Hyperion (if used) also needs to be configured! (HyperCon -> External -> Json Server/Proto Server)
// "forwarder" :
// {
// "proto" : ["127.0.0.1:19447"],
// "json" : ["127.0.0.1:19446"]
// },
/// The configuration for the frame-grabber, contains the following items:
/// * width : The width of the grabbed frames [pixels]
/// * height : The height of the grabbed frames [pixels]
/// * frequency_Hz : The frequency of the frame grab [Hz]
/// * priority : The priority of the frame-gabber (Default=890) HINT: lower value result in HIGHER priority!
/// * ATTENTION : Power-of-Two resolution is not supported and leads to unexpected behaviour!
"framegrabber" :
{
"width" : 64,
"height" : 64,
"frequency_Hz" : 10.0,
"priority" : 890
},
/// The configuration of the Kodi connection used to enable and disable the frame-grabber. Contains the following fields:
/// * xbmcAddress : The IP address of the Kodi-host
/// * xbmcTcpPort : The TCP-port of the Kodi-server
/// * grabVideo : Flag indicating that the frame-grabber is on(true) during video playback
/// * grabPictures : Flag indicating that the frame-grabber is on(true) during picture show
/// * grabAudio : Flag indicating that the frame-grabber is on(true) during audio playback
/// * grabMenu : Flag indicating that the frame-grabber is on(true) at the Kodi menu
/// * grabScreensaver : Flag indicating that the frame-grabber is on(true) when Kodi is on screensaver
/// * enable3DDetection : Flag indicating that the frame-grabber should switch to a 3D compatible modus if a 3D video is playing
"xbmcVideoChecker" :
{
"xbmcAddress" : "127.0.0.100",
"xbmcTcpPort" : 9090,
"grabVideo" : true,
"grabPictures" : true,
"grabAudio" : true,
"grabMenu" : false,
"grabScreensaver" : true,
"enable3DDetection" : true
},
/// The configuration of the Json server which enables the json remote interface
/// * port : Port at which the json server is started
"jsonServer" :
{
"port" : 19444
},
/// The configuration of the Proto server which enables the protobuffer remote interface
/// * port : Port at which the protobuffer server is started
"protoServer" :
{
"port" : 19445
},
/// The configuration of the boblight server which enables the boblight remote interface
/// * port : Port at which the boblight server is started
/// * priority: Priority of the boblight server (Default=900) HINT: lower value result in HIGHER priority!
// "boblightServer" :
// {
// "port" : 19333,
// "priority" : 900
// },
/// Configuration for the embedded V4L2 grabber
/// * device : V4L2 Device to use [default="/dev/video0"]
/// * input : V4L2 input to use [default=0]
/// * standard : Video standard (no-change/PAL/NTSC) [default="no-change"]
/// * width : V4L2 width to set [default=-1]
/// * height : V4L2 height to set [default=-1]
/// * frameDecimation : Frame decimation factor [default=2]
/// * sizeDecimation : Size decimation factor [default=8]
/// * priority : Hyperion priority channel [default=900]
/// * mode : 3D mode to use 2D/3DSBS/3DTAB (note: no autodetection) [default="2D"]
/// * cropLeft : Cropping from the left [default=0]
/// * cropRight : Cropping from the right [default=0]
/// * cropTop : Cropping from the top [default=0]
/// * cropBottom : Cropping from the bottom [default=0]
/// * redSignalThreshold : Signal threshold for the red channel between 0.0 and 1.0 [default=0.0]
/// * greenSignalThreshold : Signal threshold for the green channel between 0.0 and 1.0 [default=0.0]
/// * blueSignalThreshold : Signal threshold for the blue channel between 0.0 and 1.0 [default=0.0]
// "grabber-v4l2" :
// {
// "device" : "/dev/video0",
// "input" : 0,
// "standard" : "no-change",
// "width" : -1,
// "height" : -1,
// "frameDecimation" : 2,
// "sizeDecimation" : 8,
// "priority" : 900,
// "mode" : "2D",
// "cropLeft" : 0,
// "cropRight" : 0,
// "cropTop" : 0,
// "cropBottom" : 0,
// "redSignalThreshold" : 0.0,
// "greenSignalThreshold" : 0.0,
// "blueSignalThreshold" : 0.0
// },
/// The configuration for each individual led. This contains the specification of the area
/// averaged of an input image for each led to determine its color. Each item in the list
/// contains the following fields:
/// * index: The index of the led. This determines its location in the string of leds; zero
/// being the first led.
/// * hscan: The fractional part of the image along the horizontal used for the averaging
/// (minimum and maximum inclusive)
/// * vscan: The fractional part of the image along the vertical used for the averaging
/// (minimum and maximum inclusive)
"leds" :
[
{
"index" : 0,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9545, "maximum" : 1.0000 }
},
{
"index" : 1,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9091, "maximum" : 0.9545 }
},
{
"index" : 2,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8636, "maximum" : 0.9091 }
},
{
"index" : 3,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8182, "maximum" : 0.8636 }
},
{
"index" : 4,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7727, "maximum" : 0.8182 }
},
{
"index" : 5,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7273, "maximum" : 0.7727 }
},
{
"index" : 6,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6818, "maximum" : 0.7273 }
},
{
"index" : 7,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6364, "maximum" : 0.6818 }
},
{
"index" : 8,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5909, "maximum" : 0.6364 }
},
{
"index" : 9,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5455, "maximum" : 0.5909 }
},
{
"index" : 10,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5455 }
},
{
"index" : 11,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4545, "maximum" : 0.5000 }
},
{
"index" : 12,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4091, "maximum" : 0.4545 }
},
{
"index" : 13,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3636, "maximum" : 0.4091 }
},
{
"index" : 14,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3182, "maximum" : 0.3636 }
},
{
"index" : 15,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2727, "maximum" : 0.3182 }
},
{
"index" : 16,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2273, "maximum" : 0.2727 }
},
{
"index" : 17,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1818, "maximum" : 0.2273 }
},
{
"index" : 18,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1364, "maximum" : 0.1818 }
},
{
"index" : 19,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0909, "maximum" : 0.1364 }
},
{
"index" : 20,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0455, "maximum" : 0.0909 }
},
{
"index" : 21,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0455 }
},
{
"index" : 22,
"hscan" : { "minimum" : 0.9744, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 23,
"hscan" : { "minimum" : 0.9487, "maximum" : 0.9744 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 24,
"hscan" : { "minimum" : 0.9231, "maximum" : 0.9487 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 25,
"hscan" : { "minimum" : 0.8974, "maximum" : 0.9231 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 26,
"hscan" : { "minimum" : 0.8718, "maximum" : 0.8974 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 27,
"hscan" : { "minimum" : 0.8462, "maximum" : 0.8718 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 28,
"hscan" : { "minimum" : 0.8205, "maximum" : 0.8462 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 29,
"hscan" : { "minimum" : 0.7949, "maximum" : 0.8205 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 30,
"hscan" : { "minimum" : 0.7692, "maximum" : 0.7949 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 31,
"hscan" : { "minimum" : 0.7436, "maximum" : 0.7692 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 32,
"hscan" : { "minimum" : 0.7179, "maximum" : 0.7436 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 33,
"hscan" : { "minimum" : 0.6923, "maximum" : 0.7179 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 34,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.6923 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 35,
"hscan" : { "minimum" : 0.6410, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 36,
"hscan" : { "minimum" : 0.6154, "maximum" : 0.6410 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 37,
"hscan" : { "minimum" : 0.5897, "maximum" : 0.6154 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 38,
"hscan" : { "minimum" : 0.5641, "maximum" : 0.5897 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 39,
"hscan" : { "minimum" : 0.5385, "maximum" : 0.5641 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 40,
"hscan" : { "minimum" : 0.5128, "maximum" : 0.5385 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 41,
"hscan" : { "minimum" : 0.4872, "maximum" : 0.5128 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 42,
"hscan" : { "minimum" : 0.4615, "maximum" : 0.4872 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 43,
"hscan" : { "minimum" : 0.4359, "maximum" : 0.4615 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 44,
"hscan" : { "minimum" : 0.4103, "maximum" : 0.4359 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 45,
"hscan" : { "minimum" : 0.3846, "maximum" : 0.4103 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 46,
"hscan" : { "minimum" : 0.3590, "maximum" : 0.3846 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 47,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3590 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 48,
"hscan" : { "minimum" : 0.3077, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 49,
"hscan" : { "minimum" : 0.2821, "maximum" : 0.3077 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 50,
"hscan" : { "minimum" : 0.2564, "maximum" : 0.2821 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 51,
"hscan" : { "minimum" : 0.2308, "maximum" : 0.2564 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 52,
"hscan" : { "minimum" : 0.2051, "maximum" : 0.2308 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 53,
"hscan" : { "minimum" : 0.1795, "maximum" : 0.2051 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 54,
"hscan" : { "minimum" : 0.1538, "maximum" : 0.1795 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 55,
"hscan" : { "minimum" : 0.1282, "maximum" : 0.1538 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 56,
"hscan" : { "minimum" : 0.1026, "maximum" : 0.1282 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 57,
"hscan" : { "minimum" : 0.0769, "maximum" : 0.1026 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 58,
"hscan" : { "minimum" : 0.0513, "maximum" : 0.0769 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 59,
"hscan" : { "minimum" : 0.0256, "maximum" : 0.0513 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 60,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0256 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 61,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0455 }
},
{
"index" : 62,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0455, "maximum" : 0.0909 }
},
{
"index" : 63,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0909, "maximum" : 0.1364 }
},
{
"index" : 64,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1364, "maximum" : 0.1818 }
},
{
"index" : 65,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1818, "maximum" : 0.2273 }
},
{
"index" : 66,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2273, "maximum" : 0.2727 }
},
{
"index" : 67,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2727, "maximum" : 0.3182 }
},
{
"index" : 68,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3182, "maximum" : 0.3636 }
},
{
"index" : 69,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3636, "maximum" : 0.4091 }
},
{
"index" : 70,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4091, "maximum" : 0.4545 }
},
{
"index" : 71,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4545, "maximum" : 0.5000 }
},
{
"index" : 72,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5455 }
},
{
"index" : 73,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5455, "maximum" : 0.5909 }
},
{
"index" : 74,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5909, "maximum" : 0.6364 }
},
{
"index" : 75,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6364, "maximum" : 0.6818 }
},
{
"index" : 76,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6818, "maximum" : 0.7273 }
},
{
"index" : 77,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7273, "maximum" : 0.7727 }
},
{
"index" : 78,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7727, "maximum" : 0.8182 }
},
{
"index" : 79,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8182, "maximum" : 0.8636 }
},
{
"index" : 80,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8636, "maximum" : 0.9091 }
},
{
"index" : 81,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.9091, "maximum" : 0.9545 }
},
{
"index" : 82,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.9545, "maximum" : 1.0000 }
},
{
"index" : 83,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0256 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 84,
"hscan" : { "minimum" : 0.0256, "maximum" : 0.0513 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 85,
"hscan" : { "minimum" : 0.0513, "maximum" : 0.0769 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 86,
"hscan" : { "minimum" : 0.0769, "maximum" : 0.1026 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 87,
"hscan" : { "minimum" : 0.1026, "maximum" : 0.1282 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 88,
"hscan" : { "minimum" : 0.1282, "maximum" : 0.1538 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 89,
"hscan" : { "minimum" : 0.1538, "maximum" : 0.1795 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 90,
"hscan" : { "minimum" : 0.1795, "maximum" : 0.2051 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 91,
"hscan" : { "minimum" : 0.2051, "maximum" : 0.2308 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 92,
"hscan" : { "minimum" : 0.2308, "maximum" : 0.2564 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 93,
"hscan" : { "minimum" : 0.2564, "maximum" : 0.2821 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 94,
"hscan" : { "minimum" : 0.2821, "maximum" : 0.3077 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 95,
"hscan" : { "minimum" : 0.3077, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 96,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3590 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 97,
"hscan" : { "minimum" : 0.3590, "maximum" : 0.3846 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 98,
"hscan" : { "minimum" : 0.6154, "maximum" : 0.6410 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 99,
"hscan" : { "minimum" : 0.6410, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 100,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.6923 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 101,
"hscan" : { "minimum" : 0.6923, "maximum" : 0.7179 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 102,
"hscan" : { "minimum" : 0.7179, "maximum" : 0.7436 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 103,
"hscan" : { "minimum" : 0.7436, "maximum" : 0.7692 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 104,
"hscan" : { "minimum" : 0.7692, "maximum" : 0.7949 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 105,
"hscan" : { "minimum" : 0.7949, "maximum" : 0.8205 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 106,
"hscan" : { "minimum" : 0.8205, "maximum" : 0.8462 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 107,
"hscan" : { "minimum" : 0.8462, "maximum" : 0.8718 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 108,
"hscan" : { "minimum" : 0.8718, "maximum" : 0.8974 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 109,
"hscan" : { "minimum" : 0.8974, "maximum" : 0.9231 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 110,
"hscan" : { "minimum" : 0.9231, "maximum" : 0.9487 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 111,
"hscan" : { "minimum" : 0.9487, "maximum" : 0.9744 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 112,
"hscan" : { "minimum" : 0.9744, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
}
],
"endOfJson" : "endOfJson"
}
5.
6. DIe erste LED soll mit Blick auf den Fernseher unten rechts beginnen (Habe die LED jedoch noch nicht am TV montiert.)
7. Die Steuerung gelang mir weder mit einer der Apps noch mit dem JAVA-Programm
8.
Code: Alles auswählen
OpenELEC:~ # /storage/hyperion/bin/hyperiond.sh /storage/.config/hyperion.config
.json
Hyperion Ambilight Deamon
Version : V1.01.1 (brindosch-d4ad877/fc7bc3c-1458755689
Build Time: Mar 23 2016 14:20:16
INFO: Selected configuration file: /storage/.config/hyperion.config.json
HYPERION INFO: ColorTransform 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
LEDDEVICE INFO: configuration:
{
"colorOrder" : "rgb",
"name" : "MyHyperionConfig",
"output" : "/dev/spidev0.0",
"rate" : 250000,
"type" : "ws2801"
}
INFO: Creating linear smoothing
HYPERION (CS) INFO: Created linear-smoothing(interval_ms=40;settlingTime_ms=100; updateDelay=0
EFFECTENGINE INFO: Initializing Python interpreter
INFO: Hyperion started and initialised
INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow s wirl fast on channel 0
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
started
INFO: Kodi checker created and started
INFO: Json server created and started on port 19444
INFO: Proto server created and started on port 19445
DISPMANXGRABBER INFO: Display opened with resolution: 1920x1080
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
INFO: Frame grabber created and started
KODICHECK ERROR: Kodi Connection error (0)
BORDER SWITCH REQUIRED!!
CURRENT BORDER TYPE: unknown=0 hor.size=2 vert.size=2
EFFECTENGINE INFO: effect finished
KODICHECK ERROR: Kodi Connection error (0)
KODICHECK ERROR: Kodi Connection error (0)
.json
Hyperion Ambilight Deamon
Version : V1.01.1 (brindosch-d4ad877/fc7bc3c-1458755689
Build Time: Mar 23 2016 14:20:16
INFO: Selected configuration file: /storage/.config/hyperion.config.json
HYPERION INFO: ColorTransform 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
LEDDEVICE INFO: configuration:
{
"colorOrder" : "rgb",
"name" : "MyHyperionConfig",
"output" : "/dev/spidev0.0",
"rate" : 250000,
"type" : "ws2801"
}
INFO: Creating linear smoothing
HYPERION (CS) INFO: Created linear-smoothing(interval_ms=40;settlingTime_ms=100; updateDelay=0
EFFECTENGINE INFO: Initializing Python interpreter
INFO: Hyperion started and initialised
INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow s wirl fast on channel 0
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
started
INFO: Kodi checker created and started
INFO: Json server created and started on port 19444
INFO: Proto server created and started on port 19445
DISPMANXGRABBER INFO: Display opened with resolution: 1920x1080
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
INFO: Frame grabber created and started
KODICHECK ERROR: Kodi Connection error (0)
BORDER SWITCH REQUIRED!!
CURRENT BORDER TYPE: unknown=0 hor.size=2 vert.size=2
EFFECTENGINE INFO: effect finished
KODICHECK ERROR: Kodi Connection error (0)
KODICHECK ERROR: Kodi Connection error (0)
KODICHECK ERROR: Kodi Connection error (0)
OpenELEC:~ # /storage/hyperion/bin/hyperiond.sh /storage/.config/hyperion.config
.json
Hyperion Ambilight Deamon
Version : V1.01.1 (brindosch-d4ad877/fc7bc3c-1458755689
Build Time: Mar 23 2016 14:20:16
INFO: Selected configuration file: /storage/.config/hyperion.config.json
HYPERION INFO: ColorTransform 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
LEDDEVICE INFO: configuration:
{
"colorOrder" : "rgb",
"name" : "MyHyperionConfig",
"output" : "/dev/spidev0.0",
"rate" : 250000,
"type" : "ws2801"
}
INFO: Creating linear smoothing
HYPERION (CS) INFO: Created linear-smoothing(interval_ms=40;settlingTime_ms=100; updateDelay=0
EFFECTENGINE INFO: Initializing Python interpreter
INFO: Hyperion started and initialised
INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow s wirl fast on channel 0
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
started
INFO: Kodi checker created and started
INFO: Json server created and started on port 19444
INFO: Proto server created and started on port 19445
DISPMANXGRABBER INFO: Display opened with resolution: 1920x1080
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
INFO: Frame grabber created and started
KODICHECK ERROR: Kodi Connection error (0)
BORDER SWITCH REQUIRED!!
CURRENT BORDER TYPE: unknown=0 hor.size=2 vert.size=2
EFFECTENGINE INFO: effect finished
KODICHECK ERROR: Kodi Connection error (0)
KODICHECK ERROR: Kodi Connection error (0)
.json
Hyperion Ambilight Deamon
Version : V1.01.1 (brindosch-d4ad877/fc7bc3c-1458755689
Build Time: Mar 23 2016 14:20:16
INFO: Selected configuration file: /storage/.config/hyperion.config.json
HYPERION INFO: ColorTransform 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
HYPERION INFO: ColorCorrection 'default' => [0; 112]
LEDDEVICE INFO: configuration:
{
"colorOrder" : "rgb",
"name" : "MyHyperionConfig",
"output" : "/dev/spidev0.0",
"rate" : 250000,
"type" : "ws2801"
}
INFO: Creating linear smoothing
HYPERION (CS) INFO: Created linear-smoothing(interval_ms=40;settlingTime_ms=100; updateDelay=0
EFFECTENGINE INFO: Initializing Python interpreter
INFO: Hyperion started and initialised
INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE KODICHECK ERROR: Kodi Connection error (0)
LED blinken lediglich
Verfasst: 15. Apr 2016, 00:55
von chrisT2k
LED blinken lediglich
Verfasst: 15. Apr 2016, 10:35
von b2un0
KODICHECK ERROR: Kodi Connection error (0)
Im Kodi unter Dienste "Fernbedienung" aktivieren.
LED blinken lediglich
Verfasst: 15. Apr 2016, 12:54
von chrisT2k
Mit eingeschalteter Fernbedienung bekomme ich nun folgendes Ergebnis
Code: Alles auswählen
OpenELEC:~ # /storage/hyperion/bin/hyperiond.sh /storage/.config/hyperion.config
.json
Hyperion Ambilight Deamon
Version : V1.01.1 (brindosch-d4ad877/fc7bc3c-1458755689
Build Time: Mar 23 2016 14:20:16
INFO: Selected configuration file: /storage/.config/hyperion.config.json
HYPERION INFO: ColorTransform 'default' => [0; 104]
HYPERION INFO: ColorCorrection 'default' => [0; 104]
HYPERION INFO: ColorCorrection 'default' => [0; 104]
LEDDEVICE INFO: configuration:
{
"colorOrder" : "bgr",
"name" : "MyHyperionConfig",
"output" : "/dev/spidev0.0",
"rate" : 1000000,
"type" : "ws2801"
}
INFO: Creating linear smoothing
HYPERION (CS) INFO: Created linear-smoothing(interval_ms=40;settlingTime_ms=100; updateDelay=0
EFFECTENGINE INFO: Initializing Python interpreter
INFO: Hyperion started and initialised
INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow s wirl fast on channel 0
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
started
INFO: Kodi checker created and started
INFO: Json server created and started on port 19444
INFO: Proto server created and started on port 19445
DISPMANXGRABBER INFO: Display opened with resolution: 1920x1080
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
INFO: Frame grabber created and started
KODICHECK INFO: Kodi Connected
KODICHECK INFO: Kodi Message: {"id":666,"jsonrpc":"2.0","result":[]}
KODICHECK INFO: switching to OFF mode
KODICHECK INFO: Kodi Message: {"id":668,"jsonrpc":"2.0","result":{"System.Screen SaverActive":false}}
KODICHECK INFO: Kodi Message: {"id":670,"jsonrpc":"2.0","result":{"version":{"ma jor":15,"minor":2,"revision":"02e7013","tag":"stable"}}}
EFFECTENGINE INFO: effect finished
^CINFO: Application closed with code 0
KODICHECK INFO: Kodi Disconnected
EFFECTENGINE INFO: Cleaning up Python interpreter
Dennoch tut sich am Stripe nichts, außer dass die ersten LED weiter munter vor sich herblinken.
LED blinken lediglich
Verfasst: 15. Apr 2016, 13:05
von Avalox2k
Du hast in der config.txt vor dem " dtparam=spi=on" ein Leerzeichen. Lösch das mal raus.
LED blinken lediglich
Verfasst: 15. Apr 2016, 13:09
von b2un0
Das Leerzeichen ist egal, wenn das falsch wäre würde Hyperion nicht starten weil er das Device nicht findet
Wenn das jetzt nicht geht ist deine Verkabelung fehlerhaft, die Lötpunkte kalt/fehlerhaft oder die erste LED kaputt.
LED blinken lediglich
Verfasst: 15. Apr 2016, 13:11
von Avalox2k
b2un0 hat geschrieben:Das Leerzeichen ist egal, wenn das falsch wäre würde Hyperion nicht starten weil er das Device nicht findet
Echt ? Wieder was gelernt
LED blinken lediglich
Verfasst: 15. Apr 2016, 13:51
von chrisT2k
b2un0 hat geschrieben:Wenn das jetzt nicht geht ist deine Verkabelung fehlerhaft, die Lötpunkte kalt/fehlerhaft oder die erste LED kaputt.
Ich danke schonmal für die Hilfe. Also die Verkabelung habe ich gerade nochmals kontrolliert. Hier sind alle Punkte miteinander verbunden, die verbunden werden sollten (zumindest sieht es genauso aus, wie in der Anleitung). Die Lötpunkte sollten auch nicht mehr kalt sein (habe gerade nochmal alle kontrolliert). Auch mit dem Spannungsprüfer bekomme ich einen Kontakt zwischen den einzelnen Lötpunkten. Und auch die erste LED blinkt, wenn der Stripe am Netzteil hängt. Ich bin nun ratlos
LED blinken lediglich
Verfasst: 15. Apr 2016, 14:05
von b2un0
Schließ die beiden Datenleitungen einfach mal an nem anderen Eingang deiner Stripes an und guck obs von da geht um einen defekt des Stripes oder der jetzt ersten LED auszuschließen.
LED blinken lediglich
Verfasst: 15. Apr 2016, 20:20
von chrisT2k
Ich habe eben mal die erste LED abgetrennt und die Kabel an die 2.LED angeschlossen .. Hier der selbe Effekt, es blinkt nur
LED blinken lediglich
Verfasst: 17. Apr 2016, 20:16
von chrisT2k
Hätte noch jemand eine Idee? Habe den ersten Stripe komplett abgetrennt .. Netzteil und GPIO am zweiten Stripe angeschlossen.. Sobald die LED Strom bekommen, blinken einzelne LED immer wieder, auch wenn sie danach amRasPi angeschlossen werden ..
LED blinken lediglich
Verfasst: 18. Apr 2016, 10:36
von b2un0
Durch das direkte Löten an den GPIO Ports könnten diese defekt sein - hatten wir hier auch schon mehrfach.
LED blinken lediglich
Verfasst: 18. Apr 2016, 12:57
von chrisT2k
Gibt es da eine Möglichkeit das zu testen bzw. an irgendwelche anderen Pins zu gehen, die Daten übertragen ? Oder würde da nur ein neuer RasPi helfen ?
