Seite 1 von 5
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 13:22
von FireBirds
Hi.
Habe den Pi3 mit Openelec und alles soweit eingerichtet.
Es leuchten nur unten die 16 LEDs ab dann wo es in der Ecke mit Kabel verbunden ist, die leuchten einfach nicht.
Ist das ne Einstellung das nur diese 16LEDs bis zum Kabel leuchten?
Würde ja gerne das Ambilight Testimage nutzen aber der Pi3 bootet dann nicht.
Was habe ihr für Tips?
Gruß FireBirds
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 13:40
von cenyal
Du musst mehr infos geben.. Sonst können wir nicht Hellsehen
-Wieviele LEDs insgesamt
-Wieviele LEDs bis zu ecke ?
-Sind die ecken gelötet ? oder schnellverbinder ?
Test image für RPI3 ist vorhanden ->
https://data.z-index.net/openelec_kodi_ ... t_rpi3.zip
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 14:19
von FireBirds
97 LEDs insgesamt.
16 LEDs bis zur Ecke
Die Ecken sind gelötet. Die Eckverbinder gehen nicht da + und - vertauscht sind.
Ich Teste mal das Image. Danke.
Mit dem Testimage funktionieren nur die 16 LEDs ab den gelöteten Kabel geht keine mehr.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 15:07
von cenyal
Dann ist 100% deine Lötstelle nicht in Ordnung. Check dir deine lötstellen.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:00
von FireBirds
Habe jetzt noch mal neu gelötet. (Ich kann löten). ab da wo es mit Kabel gelötet ist leuchten die nicht.
Belegung ist 1:1 oder habe ich da einen Denkfehler?
So langsam weiß ich auch nichts mehr.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:05
von cenyal
Kannst du mal ein Bild von der Stelle posten? Wo du gelötet hast.. ab 16. LED.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:23
von FireBirds
Was ich jetzt durch Zufall gesehen habe das ab und zu mal leicht die erste LED am gelöteten Stecker manchmal etwas zuckt.
Vorher waren Kabel angelötet da ging es auch nicht und habe es jetzt mit dieser Steckleiste probiert.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:27
von cenyal
Machst bitte ein Bild damit man beide strips sehen kann. Ich denke du hast Pfeil richtung nicht beachtet. Mach bitte ein bild wo beide strips sichtbar sind.
Sonst fällt mir nicht was anderes ein. Lötstellen sehen gut aus.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:34
von FireBirds
Bin auch mittlerweile Total überfragt.
Letzte Nacht deswegen bis 4:30h aufgewesen
Nicht wundern, beim Fotografieren sind zwei Kabel rechts mit drauf.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:41
von cenyal
zu letzt bitte noch Hyperion.config.json hier posten... Die lötstellen und Laufrichtung ist ok.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:46
von FireBirds
Die LEDs leuchten bei Openelec und dem Testimage nicht nach den gelöteten Steckern.
Im moment habe ich das Testimage im Pi3.
Die Hyperion.config stimmt ja jetzt nicht mehr von der Anzahl der LEDs.
Code: Alles auswählen
// Automatically generated configuration file for 'Hyperion daemon'
// Generated by: HyperCon (The Hyperion deamon configuration file builder
{
/// Device configuration contains the following fields:
/// * 'name' : The user friendly name of the device (only used for display purposes)
/// * 'type' : The type of the device or leds (known types for now are 'ws2801', 'ldp8806',
/// 'lpd6803', 'sedu', 'adalight', 'lightpack', 'test' and 'none')
/// * 'output' : The output specification depends on selected device. This can for example be the
/// device specifier, device serial number, or the output file name
/// * 'rate' : The baudrate of the output to the device
/// * 'colorOrder' : The order of the color bytes ('rgb', 'rbg', 'bgr', etc.).
"device" :
{
"name" : "MyPi",
"type" : "ws2801",
"output" : "/dev/spidev0.0",
"rate" : 250000,
"colorOrder" : "rgb"
},
/// Color manipulation configuration used to tune the output colors to specific surroundings.
/// The configuration contains a list of color-transforms. Each transform contains the
/// following fields:
/// * 'id' : The unique identifier of the color transformation (eg 'device_1') /// * 'leds' : The indices (or index ranges) of the leds to which this color transform applies
/// (eg '0-5, 9, 11, 12-17'). The indices are zero based. /// * 'hsv' : The manipulation in the Hue-Saturation-Value color domain with the following
/// tuning parameters:
/// - 'saturationGain' The gain adjustement of the saturation
/// - 'valueGain' The gain adjustement of the value
/// * 'red'/'green'/'blue' : The manipulation in the Red-Green-Blue color domain with the
/// following tuning parameters for each channel:
/// - 'threshold' The minimum required input value for the channel to be on
/// (else zero)
/// - 'gamma' The gamma-curve correction factor
/// - 'blacklevel' The lowest possible value (when the channel is black)
/// - 'whitelevel' The highest possible value (when the channel is white)
///
/// Next to the list with color transforms there is also a smoothing option.
/// * 'smoothing' : Smoothing of the colors in the time-domain with the following tuning
/// parameters:
/// - 'type' The type of smoothing algorithm ('linear' or 'none')
/// - 'time_ms' The time constant for smoothing algorithm in milliseconds
/// - 'updateFrequency' The update frequency of the leds in Hz
"color" :
{
"transform" :
[
{
"id" : "default",
"leds" : "*",
"hsv" :
{
"saturationGain" : 1.2000,
"valueGain" : 1.2000
},
"red" :
{
"threshold" : 0.1000,
"gamma" : 2.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"green" :
{
"threshold" : 0.1000,
"gamma" : 2.0000,
"blacklevel" : 0.0000,
"whitelevel" : 0.8000
},
"blue" :
{
"threshold" : 0.1000,
"gamma" : 2.0000,
"blacklevel" : 0.0000,
"whitelevel" : 0.7000
}
}
],
"smoothing" :
{
"type" : "linear",
"time_ms" : 100,
"updateFrequency" : 25.0000
}
},
/// The black border configuration, contains the following items:
/// * enable : true if the detector should be activated
/// * threshold : Value below which a pixel is regarded as black (value between 0.0 and 1.0)
"blackborderdetector" :
{
"enable" : true,
"threshold" : 0.01
},
/// The configuration of the effect engine, contains the following items:
/// * paths : An array with absolute location(s) of directories with effects
/// * bootsequence : The effect selected as 'boot sequence'
"effects" :
{
"paths" :
[
"/storage/hyperion/effects"
]
},
"bootsequence" :
{
"effect" : "Rainbow swirl fast",
"duration_ms" : 3000
},
/// The configuration for the frame-grabber, contains the following items:
/// * width : The width of the grabbed frames [pixels]
/// * height : The height of the grabbed frames [pixels]
/// * frequency_Hz : The frequency of the frame grab [Hz]
// "framegrabber" :
// {
// "width" : 64,
// "height" : 64,
// "frequency_Hz" : 10.0
// },
/// The configuration of the XBMC connection used to enable and disable the frame-grabber. Contains the following fields:
/// * xbmcAddress : The IP address of the XBMC-host
/// * xbmcTcpPort : The TCP-port of the XBMC-server
/// * grabVideo : Flag indicating that the frame-grabber is on(true) during video playback
/// * grabPictures : Flag indicating that the frame-grabber is on(true) during picture show
/// * grabAudio : Flag indicating that the frame-grabber is on(true) during audio playback
/// * grabMenu : Flag indicating that the frame-grabber is on(true) in the XBMC menu
/// * grabScreensaver : Flag indicating that the frame-grabber is on(true) when XBMC is on screensaver
/// * enable3DDetection : Flag indicating that the frame-grabber should switch to a 3D compatible modus if a 3D video is playing
"xbmcVideoChecker" :
{
"xbmcAddress" : "127.0.0.1",
"xbmcTcpPort" : 9090,
"grabVideo" : true,
"grabPictures" : true,
"grabAudio" : true,
"grabMenu" : false,
"grabScreensaver" : true,
"enable3DDetection" : true
},
/// The configuration of the Json server which enables the json remote interface
/// * port : Port at which the json server is started
"jsonServer" :
{
"port" : 19444
},
/// The configuration of the Proto server which enables the protobuffer remote interface
/// * port : Port at which the protobuffer server is started
"protoServer" :
{
"port" : 19445
},
/// The configuration of the boblight server which enables the boblight remote interface
/// * port : Port at which the boblight server is started
// "boblightServer" :
// {
// "port" : 19333
// },
/// Configuration for the embedded V4L2 grabber
/// * device : V4L2 Device to use [default="/dev/video0"]
/// * input : V4L2 input to use [default=0]
/// * standard : Video standard (no-change/PAL/NTSC) [default="no-change"]
/// * width : V4L2 width to set [default=-1]
/// * height : V4L2 height to set [default=-1]
/// * frameDecimation : Frame decimation factor [default=2]
/// * sizeDecimation : Size decimation factor [default=8]
/// * priority : Hyperion priority channel [default=800]
/// * mode : 3D mode to use 2D/3DSBS/3DTAB (note: no autodetection) [default="2D"]
/// * cropLeft : Cropping from the left [default=0]
/// * cropRight : Cropping from the right [default=0]
/// * cropTop : Cropping from the top [default=0]
/// * cropBottom : Cropping from the bottom [default=0]
/// * redSignalThreshold : Signal threshold for the red channel between 0.0 and 1.0 [default=0.0]
/// * greenSignalThreshold : Signal threshold for the green channel between 0.0 and 1.0 [default=0.0]
/// * blueSignalThreshold : Signal threshold for the blue channel between 0.0 and 1.0 [default=0.0]
"grabber-v4l2" :
{
"device" : "/dev/video0",
"input" : 0,
"standard" : "no-change",
"width" : -1,
"height" : -1,
"frameDecimation" : 2,
"sizeDecimation" : 8,
"priority" : 800,
"mode" : "2D",
"cropLeft" : 0,
"cropRight" : 0,
"cropTop" : 0,
"cropBottom" : 0,
"redSignalThreshold" : 0.0,
"greenSignalThreshold" : 0.0,
"blueSignalThreshold" : 0.0
},
/// The configuration for each individual led. This contains the specification of the area
/// averaged of an input image for each led to determine its color. Each item in the list
/// contains the following fields:
/// * index: The index of the led. This determines its location in the string of leds; zero
/// being the first led.
/// * hscan: The fractional part of the image along the horizontal used for the averaging
/// (minimum and maximum inclusive)
/// * vscan: The fractional part of the image along the vertical used for the averaging
/// (minimum and maximum inclusive)
"leds" :
[
{
"index" : 0,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1667, "maximum" : 0.2222 }
},
{
"index" : 1,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2222, "maximum" : 0.2778 }
},
{
"index" : 2,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2778, "maximum" : 0.3333 }
},
{
"index" : 3,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3333, "maximum" : 0.3889 }
},
{
"index" : 4,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3889, "maximum" : 0.4444 }
},
{
"index" : 5,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4444, "maximum" : 0.5000 }
},
{
"index" : 6,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5556 }
},
{
"index" : 7,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5556, "maximum" : 0.6111 }
},
{
"index" : 8,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6111, "maximum" : 0.6667 }
},
{
"index" : 9,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6667, "maximum" : 0.7222 }
},
{
"index" : 10,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7222, "maximum" : 0.7778 }
},
{
"index" : 11,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7778, "maximum" : 0.8333 }
},
{
"index" : 12,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8333, "maximum" : 0.8889 }
},
{
"index" : 13,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8889, "maximum" : 0.9444 }
},
{
"index" : 14,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.9444, "maximum" : 1.0000 }
},
{
"index" : 15,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 16,
"hscan" : { "minimum" : 0.0333, "maximum" : 0.0667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 17,
"hscan" : { "minimum" : 0.0667, "maximum" : 0.1000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 18,
"hscan" : { "minimum" : 0.1000, "maximum" : 0.1333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 19,
"hscan" : { "minimum" : 0.1333, "maximum" : 0.1667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 20,
"hscan" : { "minimum" : 0.1667, "maximum" : 0.2000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 21,
"hscan" : { "minimum" : 0.2000, "maximum" : 0.2333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 22,
"hscan" : { "minimum" : 0.2333, "maximum" : 0.2667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 23,
"hscan" : { "minimum" : 0.2667, "maximum" : 0.3000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 24,
"hscan" : { "minimum" : 0.3000, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 25,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 26,
"hscan" : { "minimum" : 0.3667, "maximum" : 0.4000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 27,
"hscan" : { "minimum" : 0.4000, "maximum" : 0.4333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 28,
"hscan" : { "minimum" : 0.4333, "maximum" : 0.4667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 29,
"hscan" : { "minimum" : 0.4667, "maximum" : 0.5000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 30,
"hscan" : { "minimum" : 0.5333, "maximum" : 0.5667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 31,
"hscan" : { "minimum" : 0.5667, "maximum" : 0.6000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 32,
"hscan" : { "minimum" : 0.6000, "maximum" : 0.6333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 33,
"hscan" : { "minimum" : 0.6333, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 34,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 35,
"hscan" : { "minimum" : 0.7000, "maximum" : 0.7333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 36,
"hscan" : { "minimum" : 0.7333, "maximum" : 0.7667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 37,
"hscan" : { "minimum" : 0.7667, "maximum" : 0.8000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 38,
"hscan" : { "minimum" : 0.8000, "maximum" : 0.8333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 39,
"hscan" : { "minimum" : 0.8333, "maximum" : 0.8667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 40,
"hscan" : { "minimum" : 0.8667, "maximum" : 0.9000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 41,
"hscan" : { "minimum" : 0.9000, "maximum" : 0.9333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 42,
"hscan" : { "minimum" : 0.9333, "maximum" : 0.9667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 43,
"hscan" : { "minimum" : 0.9667, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 44,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9444, "maximum" : 1.0000 }
},
{
"index" : 45,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8889, "maximum" : 0.9444 }
},
{
"index" : 46,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8333, "maximum" : 0.8889 }
},
{
"index" : 47,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7778, "maximum" : 0.8333 }
},
{
"index" : 48,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7222, "maximum" : 0.7778 }
},
{
"index" : 49,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6667, "maximum" : 0.7222 }
},
{
"index" : 50,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6111, "maximum" : 0.6667 }
},
{
"index" : 51,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5556, "maximum" : 0.6111 }
},
{
"index" : 52,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5556 }
},
{
"index" : 53,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4444, "maximum" : 0.5000 }
},
{
"index" : 54,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3889, "maximum" : 0.4444 }
},
{
"index" : 55,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3333, "maximum" : 0.3889 }
},
{
"index" : 56,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2778, "maximum" : 0.3333 }
},
{
"index" : 57,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2222, "maximum" : 0.2778 }
},
{
"index" : 58,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1667, "maximum" : 0.2222 }
},
{
"index" : 59,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1111, "maximum" : 0.1667 }
},
{
"index" : 60,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0556, "maximum" : 0.1111 }
},
{
"index" : 61,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0556 }
},
{
"index" : 62,
"hscan" : { "minimum" : 0.9667, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 63,
"hscan" : { "minimum" : 0.9333, "maximum" : 0.9667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 64,
"hscan" : { "minimum" : 0.9000, "maximum" : 0.9333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 65,
"hscan" : { "minimum" : 0.8667, "maximum" : 0.9000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 66,
"hscan" : { "minimum" : 0.8333, "maximum" : 0.8667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 67,
"hscan" : { "minimum" : 0.8000, "maximum" : 0.8333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 68,
"hscan" : { "minimum" : 0.7667, "maximum" : 0.8000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 69,
"hscan" : { "minimum" : 0.7333, "maximum" : 0.7667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 70,
"hscan" : { "minimum" : 0.7000, "maximum" : 0.7333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 71,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 72,
"hscan" : { "minimum" : 0.6333, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 73,
"hscan" : { "minimum" : 0.6000, "maximum" : 0.6333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 74,
"hscan" : { "minimum" : 0.5667, "maximum" : 0.6000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 75,
"hscan" : { "minimum" : 0.5333, "maximum" : 0.5667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 76,
"hscan" : { "minimum" : 0.5000, "maximum" : 0.5333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 77,
"hscan" : { "minimum" : 0.4667, "maximum" : 0.5000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 78,
"hscan" : { "minimum" : 0.4333, "maximum" : 0.4667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 79,
"hscan" : { "minimum" : 0.4000, "maximum" : 0.4333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 80,
"hscan" : { "minimum" : 0.3667, "maximum" : 0.4000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 81,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 82,
"hscan" : { "minimum" : 0.3000, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 83,
"hscan" : { "minimum" : 0.2667, "maximum" : 0.3000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 84,
"hscan" : { "minimum" : 0.2333, "maximum" : 0.2667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 85,
"hscan" : { "minimum" : 0.2000, "maximum" : 0.2333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 86,
"hscan" : { "minimum" : 0.1667, "maximum" : 0.2000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 87,
"hscan" : { "minimum" : 0.1333, "maximum" : 0.1667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 88,
"hscan" : { "minimum" : 0.1000, "maximum" : 0.1333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 89,
"hscan" : { "minimum" : 0.0667, "maximum" : 0.1000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 90,
"hscan" : { "minimum" : 0.0333, "maximum" : 0.0667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 91,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 92,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0556 }
},
{
"index" : 93,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0556, "maximum" : 0.1111 }
},
{
"index" : 94,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1111, "maximum" : 0.1667 }
}
],
"endOfJson" : "endOfJson"
}
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:53
von cenyal
sieht auch gut aus.
Kann nur noch ertse LED nach der Lötstelle (17.LED Chip) defekt sein. Hast du noch rest LEDs ? kannst ab 16. die rest LED löten und schauen..
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 18:58
von FireBirds
Die rechte Leiste mit den 16LEDs leuchtet und ab da habe ich auch schon einen anderen Strang (ab 17. LED) probiert und die leuchten genauso wenig.
Deshalb bin ich ja so sprachlos und sehe da im moment keinen Sinn warum das nicht funktioniert.
Es leuchtet nach der 16. LED generell keine mehr. Warum weiß ich nicht.
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 19:20
von Avalox2k
Vielleicht die 16. Defekt? Zumindest der Ausgang zur 17.
Getippt mit meinem Galaxy S6 Edge+ mit Tapatalk
Pi3 Ambilight leuchten nur unten 16LEDs.
Verfasst: 1. Mai 2016, 19:31
von FireBirds
Habe ich gerade ausprobiert. Die 16. LED weg und dort die Kabel dran. Das selbe nach 15. LED keine leuchtet.
Anscheinend alle nach 15. LED defekt. Kann ja nur noch so sein. (Ist ja jetzt eine LED weniger).
Edit:
Die abgelötete 16. LED habe ich mit Steckverbinder angeklemmt und diese leuchtet mit Kabel.
alle anderen Stripes mit z.B. 34 LEDs oder 18 LEDs leuchtet keine einzige. Vermute mal das die alle kaputt sind.
Wenn nur eine LED mittdendrin kaputt ist, leuchten danach die anderen alle nicht?
Da macht es auch keinen Spaß umzubauen bzw. selbst zu basteln.
Werde mir vielleicht ein neues bestellen und dieses teste ich vorher ob es Komplett funktioniert.