Hy!
Hab mir heute das Ambilight nachgebaut und es läuchtet auch alles wie es soll.
Bevor ich Hyperion installiert habe, liefen alle Filme und Serien flüssig im Kodi.
Seit der Installation von Hyperion beginnen sie aber nach weinigen Sekunden zu ruckeln und der Ton setzt aus.
Ich verwende einen Pi 2 den ich auf 1,1 GHZ laut Anleitung übertaktet habe (config.txt aus der Anleitung).
Die Film- und Seriensammlung liegt auf meiner Synology NAS.
Besonders stark ist das Ruckeln bei Filmen, welche den Ganzen Bildschirm einnehmen.
Bei Filmen bei denen oben und unten ein schwarzer Balken ist, ist das Ruckeln nicht so stark.
Hat jemand ein ähnliches Problem und kann mir helfen?
Ach ja. Anscheinend gibt es vom Hyperion Config Tool eine neuere Version. Währe toll, wenn ihr die auch noch in Teil 2 des Ambilight einarbeiten könntet.
Ist zwar ziemlich gleich zu bedienen aber auf deutsch und ich glaub, dass sie etwas mehr kann (externer grabber, ...).
Filme ruckeln, seit Hyperion installiert ist
Entfern die Übertaktung, die brauchst du nicht.
Kein Support per PM!
Filme ruckeln, seit Hyperion installiert ist
Hat leider auch nichts geändert.
Würde eigentlich Hyperion auch auf nem Raspberry pi B auch laufen?
Dann würd ich es einfach auslagern da ich soundso noch vorhabe, die HDMI Erweiterung dazu zu bauen.
Würde eigentlich Hyperion auch auf nem Raspberry pi B auch laufen?
Dann würd ich es einfach auslagern da ich soundso noch vorhabe, die HDMI Erweiterung dazu zu bauen.
Filme ruckeln, seit Hyperion installiert ist
Hyperion läuft auf allen Raspberry Derivaten
Kein Support per PM!
Filme ruckeln, seit Hyperion installiert ist
Welches System hast du drauf?
OpenELEC, LibreELEC oder welches?
Und Ruckelt bei dir das Bild oder ist es nur der Ton der für 1-2 Sekunden manchmal weg ist?
OpenELEC, LibreELEC oder welches?
Und Ruckelt bei dir das Bild oder ist es nur der Ton der für 1-2 Sekunden manchmal weg ist?
Filme ruckeln, seit Hyperion installiert ist
Da ich dasselbe Problem habe, klinke ich mich hier mal mit ein:
Ich betreibe Kodi mit OpenElec 6.0.3 auf einem Raspberry Pi 2.
Seit dem Hinzufügen von Ambilight mit LEDs, Hyperion etc. bekomme ich immer wieder bei Filmen und Serien mehrere Sekunden lang kein Bild- und Tonsignal mehr an den Fernseher.
Die LEDs leuchten allerdings weiterhin passend zum nicht dargestellten Bild.
Ich betreibe Kodi mit OpenElec 6.0.3 auf einem Raspberry Pi 2.
Seit dem Hinzufügen von Ambilight mit LEDs, Hyperion etc. bekomme ich immer wieder bei Filmen und Serien mehrere Sekunden lang kein Bild- und Tonsignal mehr an den Fernseher.
Die LEDs leuchten allerdings weiterhin passend zum nicht dargestellten Bild.
Filme ruckeln, seit Hyperion installiert ist
Dann haut mal beide raus was das für Formate sind, mkv/avi (h264)? MPEG oder DVD Images?
Kein Support per PM!
Filme ruckeln, seit Hyperion installiert ist
In meinem Fall sind das .mkv-Files.
Filme ruckeln, seit Hyperion installiert ist
Wekra hat geschrieben:In meinem Fall sind das .mkv-Files.
mkv ist kein Format sondern nur ein Container.
-
nitroburger
- Neuling
- Beiträge:11
- Registriert:21. Apr 2016
Filme ruckeln, seit Hyperion installiert ist
Häng mich hier mal dran.
Habe das gleiche Problem: HD Filme im mp4-Container mit H264 Codec zeigen Bildfehler und Tonausetzter.
HD Aufnahmen (ARD HD zum Beispiel) via Sat2IP funktionieren ohne Probleme.
Wenn ich das Ambilight ausschalte, dann funktionieren die Filme?! Jemand ne Idee? Liegt es an einer falschen Hyperion-Config?
Habe das gleiche Problem: HD Filme im mp4-Container mit H264 Codec zeigen Bildfehler und Tonausetzter.
HD Aufnahmen (ARD HD zum Beispiel) via Sat2IP funktionieren ohne Probleme.
Wenn ich das Ambilight ausschalte, dann funktionieren die Filme?! Jemand ne Idee? Liegt es an einer falschen Hyperion-Config?
Filme ruckeln, seit Hyperion installiert ist
Würde ich mal behaupte, ja - postet mal eure Konfigurationen.
Kein Support per PM!
-
nitroburger
- Neuling
- Beiträge:11
- Registriert:21. Apr 2016
Filme ruckeln, seit Hyperion installiert ist
Verwende einen Raspberry Pi3 mit aktuellem Openelec und WS2801.
Hier meine aktuelle mit den Fehlern:
Und hier hätte ich mal eine neue erstellt, welche ich noch nciht getestet habe:
Hier meine aktuelle mit den Fehlern:
Code: Alles auswählen
// Automatically generated configuration file for 'Hyperion daemon'
// Generated by: HyperCon (The Hyperion deamon configuration file builder)
// Created with HyperCon V1.01.2 (31.03.2016)
{
/// Device configuration contains the following fields:
/// * 'name' : The user friendly name of the device (only used for display purposes)
/// * 'type' : The type of the device or leds (known types for now are
/// ---------SPI---------, APA102, WS2801, P9813, LPD6803, LPD8806, ---------PWM---------, WS2812b (just RPi1), WS281X (RPi1, RPi2, RPi3), --------OTHER--------, PhilipsHUE, AtmoOrb, PiBlaster, Tinkerforge, UDP, FadeCandy, SEDU, TPM2, USBASP-WS2801, USBASP-WS2812, ------3rd PARTY------, Adalight, AdalightAPA102, AmbiLed, Atmo, Lightpack, Multi-Lightpack, Paintpack, Test (file), None)
/// * [device type specific configuration]
/// * 'colorOrder' : The order of the color bytes ('rgb', 'rbg', 'bgr', etc.).
"device" :
{
"name" : "MyHyperionConfig",
"type" : "ws2801",
"output" : "/dev/spidev0.0",
"rate" : 250000,
"colorOrder" : "bgr"
},
/// Color manipulation configuration used to tune the output colors to specific surroundings.
/// The configuration contains a list of color-transforms. Each transform contains the
/// following fields:
/// * 'id' : The unique identifier of the color transformation (eg 'device_1') /// * 'leds' : The indices (or index ranges) of the leds to which this color transform applies
/// (eg '0-5, 9, 11, 12-17'). The indices are zero based. /// * 'hsv' : The manipulation in the Hue-Saturation-Value color domain with the following
/// tuning parameters:
/// - 'saturationGain' The gain adjustement of the saturation
/// - 'valueGain' The gain adjustement of the value
/// * 'red'/'green'/'blue' : The manipulation in the Red-Green-Blue color domain with the
/// following tuning parameters for each channel:
/// - 'threshold' The minimum required input value for the channel to be on
/// (else zero)
/// - 'gamma' The gamma-curve correction factor
/// - 'blacklevel' The lowest possible value (when the channel is black)
/// - 'whitelevel' The highest possible value (when the channel is white)
///
/// Next to the list with color transforms there is also a smoothing option.
/// * 'smoothing' : Smoothing of the colors in the time-domain with the following tuning
/// parameters:
/// - 'type' The type of smoothing algorithm ('linear' or 'none')
/// - 'time_ms' The time constant for smoothing algorithm in milliseconds
/// - 'updateFrequency' The update frequency of the leds in Hz
/// - 'updateDelay' The delay of the output to leds (in periods of smoothing)
"color" :
{
"correction" :
[
{
"id" : "default",
"leds" : "*",
"correctionValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"temperature" :
[
{
"id" : "default",
"leds" : "*",
"temperatureValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"transform" :
[
{
"id" : "default",
"leds" : "*",
"hsv" :
{
"saturationGain" : 1.0000,
"valueGain" : 1.0000
},
"hsl" :
{
"saturationGain" : 1.0000,
"luminanceGain" : 1.0000
},
"red" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"green" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"blue" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
}
}
],
"smoothing" :
{
"type" : "linear",
"time_ms" : 100,
"updateFrequency" : 25.0000,
"updateDelay" : 0
}
},
/// The black border configuration, contains the following items:
/// * enable : true if the detector should be activated
/// * threshold : Value below which a pixel is regarded as black (value between 0.0 and 1.0)
/// * unknownFrameCnt : Number of frames without any detection before the border is set to 0 (default 600)
/// * borderFrameCnt : Number of frames before a consistent detected border gets set (default 50)
/// * maxInconsistentCnt : Number of inconsistent frames that are ignored before a new border gets a chance to proof consistency
/// * blurRemoveCnt : Number of pixels that get removed from the detected border to cut away blur (default 1)
/// * mode : Border detection mode (values=default,classic,osd)
"blackborderdetector" :
{
"enable" : true,
"threshold" : 0.0,
"unknownFrameCnt" : 600,
"borderFrameCnt" : 50,
"maxInconsistentCnt" : 10,
"blurRemoveCnt" : 1,
"mode" : "default"
},
/// The configuration of the effect engine, contains the following items:
/// * paths : An array with absolute location(s) of directories with effects
/// * color : Set static color after boot -> set effect to "" (empty) and input the values [R,G,B] and set duration_ms NOT to 0 (use 1) instead
/// * effect : The effect selected as 'boot sequence'
/// * duration_ms : The duration of the selected effect (0=endless)
/// * priority : The priority of the selected effect/static color (default=990) HINT: lower value result in HIGHER priority!
"effects" :
{
"paths" :
[
"/storage/hyperion/effects"
]
},
// "bootsequence" :
// {
// "color" : [0,0,0],
// "effect" : "Knight rider",
// "duration_ms" : 3000,
// "priority" : 990
// },
/// The configuration of the Json/Proto forwarder. Forward messages to multiple instances of Hyperion on same and/or other hosts
/// 'proto' is mostly used for video streams and 'json' for effects
/// * proto : Proto server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19447"] or more instances to forward ["127.0.0.1:19447","192.168.0.24:19449"]
/// * json : Json server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19446"] or more instances to forward ["127.0.0.1:19446","192.168.0.24:19448"]
/// HINT: If you redirect to "127.0.0.1" (localhost) you could start a second hyperion with another device/led config!
/// Be sure your client(s) is/are listening on the configured ports. The second Hyperion (if used) also needs to be configured! (HyperCon -> External -> Json Server/Proto Server)
// "forwarder" :
// {
// "proto" : ["127.0.0.1:19447"],
// "json" : ["127.0.0.1:19446"]
// },
/// The configuration for the frame-grabber, contains the following items:
/// * width : The width of the grabbed frames [pixels]
/// * height : The height of the grabbed frames [pixels]
/// * frequency_Hz : The frequency of the frame grab [Hz]
/// * priority : The priority of the frame-gabber (Default=890) HINT: lower value result in HIGHER priority!
/// * ATTENTION : Power-of-Two resolution is not supported and leads to unexpected behaviour!
"framegrabber" :
{
"width" : 80,
"height" : 45,
"frequency_Hz" : 10.0,
"priority" : 890
},
/// The configuration of the Kodi connection used to enable and disable the frame-grabber. Contains the following fields:
/// * xbmcAddress : The IP address of the Kodi-host
/// * xbmcTcpPort : The TCP-port of the Kodi-server
/// * grabVideo : Flag indicating that the frame-grabber is on(true) during video playback
/// * grabPictures : Flag indicating that the frame-grabber is on(true) during picture show
/// * grabAudio : Flag indicating that the frame-grabber is on(true) during audio playback
/// * grabMenu : Flag indicating that the frame-grabber is on(true) at the Kodi menu
/// * grabScreensaver : Flag indicating that the frame-grabber is on(true) when Kodi is on screensaver
/// * enable3DDetection : Flag indicating that the frame-grabber should switch to a 3D compatible modus if a 3D video is playing
"xbmcVideoChecker" :
{
"xbmcAddress" : "192.168.177.248",
"xbmcTcpPort" : 9090,
"grabVideo" : true,
"grabPictures" : false,
"grabAudio" : false,
"grabMenu" : false,
"grabScreensaver" : false,
"enable3DDetection" : false
},
/// The configuration of the Json server which enables the json remote interface
/// * port : Port at which the json server is started
"jsonServer" :
{
"port" : 19444
},
/// The configuration of the Proto server which enables the protobuffer remote interface
/// * port : Port at which the protobuffer server is started
"protoServer" :
{
"port" : 19445
},
/// The configuration of the boblight server which enables the boblight remote interface
/// * port : Port at which the boblight server is started
/// * priority: Priority of the boblight server (Default=900) HINT: lower value result in HIGHER priority!
// "boblightServer" :
// {
// "port" : 19333,
// "priority" : 900
// },
/// Configuration for the embedded V4L2 grabber
/// * device : V4L2 Device to use [default="/dev/video0"]
/// * input : V4L2 input to use [default=0]
/// * standard : Video standard (no-change/PAL/NTSC) [default="no-change"]
/// * width : V4L2 width to set [default=-1]
/// * height : V4L2 height to set [default=-1]
/// * frameDecimation : Frame decimation factor [default=2]
/// * sizeDecimation : Size decimation factor [default=8]
/// * priority : Hyperion priority channel [default=900]
/// * mode : 3D mode to use 2D/3DSBS/3DTAB (note: no autodetection) [default="2D"]
/// * cropLeft : Cropping from the left [default=0]
/// * cropRight : Cropping from the right [default=0]
/// * cropTop : Cropping from the top [default=0]
/// * cropBottom : Cropping from the bottom [default=0]
/// * redSignalThreshold : Signal threshold for the red channel between 0.0 and 1.0 [default=0.0]
/// * greenSignalThreshold : Signal threshold for the green channel between 0.0 and 1.0 [default=0.0]
/// * blueSignalThreshold : Signal threshold for the blue channel between 0.0 and 1.0 [default=0.0]
// "grabber-v4l2" :
// {
// "device" : "/dev/video0",
// "input" : 0,
// "standard" : "no-change",
// "width" : -1,
// "height" : -1,
// "frameDecimation" : 2,
// "sizeDecimation" : 8,
// "priority" : 900,
// "mode" : "2D",
// "cropLeft" : 0,
// "cropRight" : 0,
// "cropTop" : 0,
// "cropBottom" : 0,
// "redSignalThreshold" : 0.0,
// "greenSignalThreshold" : 0.0,
// "blueSignalThreshold" : 0.0
// },
/// The configuration for each individual led. This contains the specification of the area
/// averaged of an input image for each led to determine its color. Each item in the list
/// contains the following fields:
/// * index: The index of the led. This determines its location in the string of leds; zero
/// being the first led.
/// * hscan: The fractional part of the image along the horizontal used for the averaging
/// (minimum and maximum inclusive)
/// * vscan: The fractional part of the image along the vertical used for the averaging
/// (minimum and maximum inclusive)
"leds" :
[
{
"index" : 0,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9375, "maximum" : 1.0000 }
},
{
"index" : 1,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8750, "maximum" : 0.9375 }
},
{
"index" : 2,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8125, "maximum" : 0.8750 }
},
{
"index" : 3,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7500, "maximum" : 0.8125 }
},
{
"index" : 4,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6875, "maximum" : 0.7500 }
},
{
"index" : 5,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6250, "maximum" : 0.6875 }
},
{
"index" : 6,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5625, "maximum" : 0.6250 }
},
{
"index" : 7,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5625 }
},
{
"index" : 8,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4375, "maximum" : 0.5000 }
},
{
"index" : 9,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3750, "maximum" : 0.4375 }
},
{
"index" : 10,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3125, "maximum" : 0.3750 }
},
{
"index" : 11,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2500, "maximum" : 0.3125 }
},
{
"index" : 12,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1875, "maximum" : 0.2500 }
},
{
"index" : 13,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1250, "maximum" : 0.1875 }
},
{
"index" : 14,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0625, "maximum" : 0.1250 }
},
{
"index" : 15,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0625 }
},
{
"index" : 16,
"hscan" : { "minimum" : 0.9630, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 17,
"hscan" : { "minimum" : 0.9259, "maximum" : 0.9630 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 18,
"hscan" : { "minimum" : 0.8889, "maximum" : 0.9259 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 19,
"hscan" : { "minimum" : 0.8519, "maximum" : 0.8889 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 20,
"hscan" : { "minimum" : 0.8148, "maximum" : 0.8519 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 21,
"hscan" : { "minimum" : 0.7778, "maximum" : 0.8148 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 22,
"hscan" : { "minimum" : 0.7407, "maximum" : 0.7778 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 23,
"hscan" : { "minimum" : 0.7037, "maximum" : 0.7407 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 24,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7037 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 25,
"hscan" : { "minimum" : 0.6296, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 26,
"hscan" : { "minimum" : 0.5926, "maximum" : 0.6296 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 27,
"hscan" : { "minimum" : 0.5556, "maximum" : 0.5926 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 28,
"hscan" : { "minimum" : 0.5185, "maximum" : 0.5556 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 29,
"hscan" : { "minimum" : 0.4815, "maximum" : 0.5185 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 30,
"hscan" : { "minimum" : 0.4444, "maximum" : 0.4815 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 31,
"hscan" : { "minimum" : 0.4074, "maximum" : 0.4444 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 32,
"hscan" : { "minimum" : 0.3704, "maximum" : 0.4074 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 33,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3704 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 34,
"hscan" : { "minimum" : 0.2963, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 35,
"hscan" : { "minimum" : 0.2593, "maximum" : 0.2963 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 36,
"hscan" : { "minimum" : 0.2222, "maximum" : 0.2593 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 37,
"hscan" : { "minimum" : 0.1852, "maximum" : 0.2222 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 38,
"hscan" : { "minimum" : 0.1481, "maximum" : 0.1852 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 39,
"hscan" : { "minimum" : 0.1111, "maximum" : 0.1481 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 40,
"hscan" : { "minimum" : 0.0741, "maximum" : 0.1111 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 41,
"hscan" : { "minimum" : 0.0370, "maximum" : 0.0741 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 42,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0370 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 43,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0625 }
},
{
"index" : 44,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0625, "maximum" : 0.1250 }
},
{
"index" : 45,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1250, "maximum" : 0.1875 }
},
{
"index" : 46,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1875, "maximum" : 0.2500 }
},
{
"index" : 47,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2500, "maximum" : 0.3125 }
},
{
"index" : 48,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3125, "maximum" : 0.3750 }
},
{
"index" : 49,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3750, "maximum" : 0.4375 }
},
{
"index" : 50,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4375, "maximum" : 0.5000 }
},
{
"index" : 51,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5625 }
},
{
"index" : 52,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5625, "maximum" : 0.6250 }
},
{
"index" : 53,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6250, "maximum" : 0.6875 }
},
{
"index" : 54,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6875, "maximum" : 0.7500 }
},
{
"index" : 55,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7500, "maximum" : 0.8125 }
},
{
"index" : 56,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8125, "maximum" : 0.8750 }
},
{
"index" : 57,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8750, "maximum" : 0.9375 }
},
{
"index" : 58,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.9375, "maximum" : 1.0000 }
},
{
"index" : 59,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0370 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 60,
"hscan" : { "minimum" : 0.0370, "maximum" : 0.0741 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 61,
"hscan" : { "minimum" : 0.0741, "maximum" : 0.1111 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 62,
"hscan" : { "minimum" : 0.1111, "maximum" : 0.1481 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 63,
"hscan" : { "minimum" : 0.1481, "maximum" : 0.1852 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 64,
"hscan" : { "minimum" : 0.1852, "maximum" : 0.2222 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 65,
"hscan" : { "minimum" : 0.2222, "maximum" : 0.2593 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 66,
"hscan" : { "minimum" : 0.2593, "maximum" : 0.2963 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 67,
"hscan" : { "minimum" : 0.2963, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 68,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3704 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 69,
"hscan" : { "minimum" : 0.3704, "maximum" : 0.4074 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 70,
"hscan" : { "minimum" : 0.4074, "maximum" : 0.4444 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 71,
"hscan" : { "minimum" : 0.4444, "maximum" : 0.4815 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 72,
"hscan" : { "minimum" : 0.4815, "maximum" : 0.5185 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 73,
"hscan" : { "minimum" : 0.5185, "maximum" : 0.5556 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 74,
"hscan" : { "minimum" : 0.5556, "maximum" : 0.5926 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 75,
"hscan" : { "minimum" : 0.5926, "maximum" : 0.6296 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 76,
"hscan" : { "minimum" : 0.6296, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 77,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7037 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 78,
"hscan" : { "minimum" : 0.7037, "maximum" : 0.7407 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 79,
"hscan" : { "minimum" : 0.7407, "maximum" : 0.7778 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 80,
"hscan" : { "minimum" : 0.7778, "maximum" : 0.8148 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 81,
"hscan" : { "minimum" : 0.8148, "maximum" : 0.8519 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 82,
"hscan" : { "minimum" : 0.8519, "maximum" : 0.8889 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 83,
"hscan" : { "minimum" : 0.8889, "maximum" : 0.9259 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 84,
"hscan" : { "minimum" : 0.9259, "maximum" : 0.9630 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 85,
"hscan" : { "minimum" : 0.9630, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
}
],
"endOfJson" : "endOfJson"
}
Und hier hätte ich mal eine neue erstellt, welche ich noch nciht getestet habe:
Code: Alles auswählen
// Automatically generated configuration file for 'Hyperion daemon'
// Generated by: HyperCon (The Hyperion deamon configuration file builder)
// Created with HyperCon V1.01.2 (31.03.2016)
{
/// Device configuration contains the following fields:
/// * 'name' : The user friendly name of the device (only used for display purposes)
/// * 'type' : The type of the device or leds (known types for now are
/// ---------SPI---------, APA102, WS2801, P9813, LPD6803, LPD8806, ---------PWM---------, WS2812b (just RPi1), WS281X (RPi1, RPi2, RPi3), --------OTHER--------, PhilipsHUE, AtmoOrb, PiBlaster, Tinkerforge, UDP, FadeCandy, SEDU, TPM2, USBASP-WS2801, USBASP-WS2812, ------3rd PARTY------, Adalight, AdalightAPA102, AmbiLed, Atmo, Lightpack, Multi-Lightpack, Paintpack, Test (file), None)
/// * [device type specific configuration]
/// * 'colorOrder' : The order of the color bytes ('rgb', 'rbg', 'bgr', etc.).
"device" :
{
"name" : "MyHyperionConfig",
"type" : "ws281x",
"leds" : 86,
"colorOrder" : "rgb"
},
/// Color manipulation configuration used to tune the output colors to specific surroundings.
/// The configuration contains a list of color-transforms. Each transform contains the
/// following fields:
/// * 'id' : The unique identifier of the color transformation (eg 'device_1') /// * 'leds' : The indices (or index ranges) of the leds to which this color transform applies
/// (eg '0-5, 9, 11, 12-17'). The indices are zero based. /// * 'hsv' : The manipulation in the Hue-Saturation-Value color domain with the following
/// tuning parameters:
/// - 'saturationGain' The gain adjustement of the saturation
/// - 'valueGain' The gain adjustement of the value
/// * 'red'/'green'/'blue' : The manipulation in the Red-Green-Blue color domain with the
/// following tuning parameters for each channel:
/// - 'threshold' The minimum required input value for the channel to be on
/// (else zero)
/// - 'gamma' The gamma-curve correction factor
/// - 'blacklevel' The lowest possible value (when the channel is black)
/// - 'whitelevel' The highest possible value (when the channel is white)
///
/// Next to the list with color transforms there is also a smoothing option.
/// * 'smoothing' : Smoothing of the colors in the time-domain with the following tuning
/// parameters:
/// - 'type' The type of smoothing algorithm ('linear' or 'none')
/// - 'time_ms' The time constant for smoothing algorithm in milliseconds
/// - 'updateFrequency' The update frequency of the leds in Hz
/// - 'updateDelay' The delay of the output to leds (in periods of smoothing)
"color" :
{
"correction" :
[
{
"id" : "default",
"leds" : "*",
"correctionValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"temperature" :
[
{
"id" : "default",
"leds" : "*",
"temperatureValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"transform" :
[
{
"id" : "default",
"leds" : "*",
"hsv" :
{
"saturationGain" : 1.0000,
"valueGain" : 1.0000
},
"hsl" :
{
"saturationGain" : 1.0000,
"luminanceGain" : 1.0000
},
"red" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"green" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"blue" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
}
}
],
"smoothing" :
{
"type" : "linear",
"time_ms" : 100,
"updateFrequency" : 25.0000,
"updateDelay" : 0
}
},
/// The black border configuration, contains the following items:
/// * enable : true if the detector should be activated
/// * threshold : Value below which a pixel is regarded as black (value between 0.0 and 1.0)
/// * unknownFrameCnt : Number of frames without any detection before the border is set to 0 (default 600)
/// * borderFrameCnt : Number of frames before a consistent detected border gets set (default 50)
/// * maxInconsistentCnt : Number of inconsistent frames that are ignored before a new border gets a chance to proof consistency
/// * blurRemoveCnt : Number of pixels that get removed from the detected border to cut away blur (default 1)
/// * mode : Border detection mode (values=default,classic,osd)
"blackborderdetector" :
{
"enable" : true,
"threshold" : 0.01,
"unknownFrameCnt" : 600,
"borderFrameCnt" : 50,
"maxInconsistentCnt" : 10,
"blurRemoveCnt" : 1,
"mode" : "default"
},
/// The configuration of the effect engine, contains the following items:
/// * paths : An array with absolute location(s) of directories with effects
/// * color : Set static color after boot -> set effect to "" (empty) and input the values [R,G,B] and set duration_ms NOT to 0 (use 1) instead
/// * effect : The effect selected as 'boot sequence'
/// * duration_ms : The duration of the selected effect (0=endless)
/// * priority : The priority of the selected effect/static color (default=990) HINT: lower value result in HIGHER priority!
"effects" :
{
"paths" :
[
"/storage/hyperion/effects"
]
},
// "bootsequence" :
// {
// "color" : [0,0,0],
// "effect" : "Rainbow swirl fast",
// "duration_ms" : 3000,
// "priority" : 990
// },
/// The configuration of the Json/Proto forwarder. Forward messages to multiple instances of Hyperion on same and/or other hosts
/// 'proto' is mostly used for video streams and 'json' for effects
/// * proto : Proto server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19447"] or more instances to forward ["127.0.0.1:19447","192.168.0.24:19449"]
/// * json : Json server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19446"] or more instances to forward ["127.0.0.1:19446","192.168.0.24:19448"]
/// HINT: If you redirect to "127.0.0.1" (localhost) you could start a second hyperion with another device/led config!
/// Be sure your client(s) is/are listening on the configured ports. The second Hyperion (if used) also needs to be configured! (HyperCon -> External -> Json Server/Proto Server)
// "forwarder" :
// {
// "proto" : ["127.0.0.1:19447"],
// "json" : ["127.0.0.1:19446"]
// },
/// The configuration for the frame-grabber, contains the following items:
/// * width : The width of the grabbed frames [pixels]
/// * height : The height of the grabbed frames [pixels]
/// * frequency_Hz : The frequency of the frame grab [Hz]
/// * priority : The priority of the frame-gabber (Default=890) HINT: lower value result in HIGHER priority!
/// * ATTENTION : Power-of-Two resolution is not supported and leads to unexpected behaviour!
"framegrabber" :
{
"width" : 80,
"height" : 45,
"frequency_Hz" : 10.0,
"priority" : 890
},
/// The configuration of the Kodi connection used to enable and disable the frame-grabber. Contains the following fields:
/// * xbmcAddress : The IP address of the Kodi-host
/// * xbmcTcpPort : The TCP-port of the Kodi-server
/// * grabVideo : Flag indicating that the frame-grabber is on(true) during video playback
/// * grabPictures : Flag indicating that the frame-grabber is on(true) during picture show
/// * grabAudio : Flag indicating that the frame-grabber is on(true) during audio playback
/// * grabMenu : Flag indicating that the frame-grabber is on(true) at the Kodi menu
/// * grabScreensaver : Flag indicating that the frame-grabber is on(true) when Kodi is on screensaver
/// * enable3DDetection : Flag indicating that the frame-grabber should switch to a 3D compatible modus if a 3D video is playing
"xbmcVideoChecker" :
{
"xbmcAddress" : "192.168.177.248",
"xbmcTcpPort" : 9090,
"grabVideo" : true,
"grabPictures" : false,
"grabAudio" : false,
"grabMenu" : false,
"grabScreensaver" : false,
"enable3DDetection" : false
},
/// The configuration of the Json server which enables the json remote interface
/// * port : Port at which the json server is started
"jsonServer" :
{
"port" : 19444
},
/// The configuration of the Proto server which enables the protobuffer remote interface
/// * port : Port at which the protobuffer server is started
"protoServer" :
{
"port" : 19445
},
/// The configuration of the boblight server which enables the boblight remote interface
/// * port : Port at which the boblight server is started
/// * priority: Priority of the boblight server (Default=900) HINT: lower value result in HIGHER priority!
// "boblightServer" :
// {
// "port" : 19333,
// "priority" : 900
// },
/// Configuration for the embedded V4L2 grabber
/// * device : V4L2 Device to use [default="/dev/video0"]
/// * input : V4L2 input to use [default=0]
/// * standard : Video standard (no-change/PAL/NTSC) [default="no-change"]
/// * width : V4L2 width to set [default=-1]
/// * height : V4L2 height to set [default=-1]
/// * frameDecimation : Frame decimation factor [default=2]
/// * sizeDecimation : Size decimation factor [default=8]
/// * priority : Hyperion priority channel [default=900]
/// * mode : 3D mode to use 2D/3DSBS/3DTAB (note: no autodetection) [default="2D"]
/// * cropLeft : Cropping from the left [default=0]
/// * cropRight : Cropping from the right [default=0]
/// * cropTop : Cropping from the top [default=0]
/// * cropBottom : Cropping from the bottom [default=0]
/// * redSignalThreshold : Signal threshold for the red channel between 0.0 and 1.0 [default=0.0]
/// * greenSignalThreshold : Signal threshold for the green channel between 0.0 and 1.0 [default=0.0]
/// * blueSignalThreshold : Signal threshold for the blue channel between 0.0 and 1.0 [default=0.0]
// "grabber-v4l2" :
// {
// "device" : "/dev/video0",
// "input" : 0,
// "standard" : "no-change",
// "width" : -1,
// "height" : -1,
// "frameDecimation" : 2,
// "sizeDecimation" : 8,
// "priority" : 900,
// "mode" : "2D",
// "cropLeft" : 0,
// "cropRight" : 0,
// "cropTop" : 0,
// "cropBottom" : 0,
// "redSignalThreshold" : 0.0,
// "greenSignalThreshold" : 0.0,
// "blueSignalThreshold" : 0.0
// },
/// The configuration for each individual led. This contains the specification of the area
/// averaged of an input image for each led to determine its color. Each item in the list
/// contains the following fields:
/// * index: The index of the led. This determines its location in the string of leds; zero
/// being the first led.
/// * hscan: The fractional part of the image along the horizontal used for the averaging
/// (minimum and maximum inclusive)
/// * vscan: The fractional part of the image along the vertical used for the averaging
/// (minimum and maximum inclusive)
"leds" :
[
{
"index" : 0,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9375, "maximum" : 1.0000 }
},
{
"index" : 1,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8750, "maximum" : 0.9375 }
},
{
"index" : 2,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8125, "maximum" : 0.8750 }
},
{
"index" : 3,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7500, "maximum" : 0.8125 }
},
{
"index" : 4,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6875, "maximum" : 0.7500 }
},
{
"index" : 5,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6250, "maximum" : 0.6875 }
},
{
"index" : 6,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5625, "maximum" : 0.6250 }
},
{
"index" : 7,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5625 }
},
{
"index" : 8,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4375, "maximum" : 0.5000 }
},
{
"index" : 9,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3750, "maximum" : 0.4375 }
},
{
"index" : 10,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3125, "maximum" : 0.3750 }
},
{
"index" : 11,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2500, "maximum" : 0.3125 }
},
{
"index" : 12,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1875, "maximum" : 0.2500 }
},
{
"index" : 13,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1250, "maximum" : 0.1875 }
},
{
"index" : 14,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0625, "maximum" : 0.1250 }
},
{
"index" : 15,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0625 }
},
{
"index" : 16,
"hscan" : { "minimum" : 0.9630, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 17,
"hscan" : { "minimum" : 0.9259, "maximum" : 0.9630 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 18,
"hscan" : { "minimum" : 0.8889, "maximum" : 0.9259 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 19,
"hscan" : { "minimum" : 0.8519, "maximum" : 0.8889 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 20,
"hscan" : { "minimum" : 0.8148, "maximum" : 0.8519 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 21,
"hscan" : { "minimum" : 0.7778, "maximum" : 0.8148 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 22,
"hscan" : { "minimum" : 0.7407, "maximum" : 0.7778 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 23,
"hscan" : { "minimum" : 0.7037, "maximum" : 0.7407 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 24,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7037 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 25,
"hscan" : { "minimum" : 0.6296, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 26,
"hscan" : { "minimum" : 0.5926, "maximum" : 0.6296 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 27,
"hscan" : { "minimum" : 0.5556, "maximum" : 0.5926 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 28,
"hscan" : { "minimum" : 0.5185, "maximum" : 0.5556 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 29,
"hscan" : { "minimum" : 0.4815, "maximum" : 0.5185 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 30,
"hscan" : { "minimum" : 0.4444, "maximum" : 0.4815 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 31,
"hscan" : { "minimum" : 0.4074, "maximum" : 0.4444 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 32,
"hscan" : { "minimum" : 0.3704, "maximum" : 0.4074 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 33,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3704 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 34,
"hscan" : { "minimum" : 0.2963, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 35,
"hscan" : { "minimum" : 0.2593, "maximum" : 0.2963 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 36,
"hscan" : { "minimum" : 0.2222, "maximum" : 0.2593 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 37,
"hscan" : { "minimum" : 0.1852, "maximum" : 0.2222 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 38,
"hscan" : { "minimum" : 0.1481, "maximum" : 0.1852 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 39,
"hscan" : { "minimum" : 0.1111, "maximum" : 0.1481 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 40,
"hscan" : { "minimum" : 0.0741, "maximum" : 0.1111 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 41,
"hscan" : { "minimum" : 0.0370, "maximum" : 0.0741 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 42,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0370 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 43,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0625 }
},
{
"index" : 44,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0625, "maximum" : 0.1250 }
},
{
"index" : 45,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1250, "maximum" : 0.1875 }
},
{
"index" : 46,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1875, "maximum" : 0.2500 }
},
{
"index" : 47,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2500, "maximum" : 0.3125 }
},
{
"index" : 48,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3125, "maximum" : 0.3750 }
},
{
"index" : 49,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3750, "maximum" : 0.4375 }
},
{
"index" : 50,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4375, "maximum" : 0.5000 }
},
{
"index" : 51,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5625 }
},
{
"index" : 52,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5625, "maximum" : 0.6250 }
},
{
"index" : 53,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6250, "maximum" : 0.6875 }
},
{
"index" : 54,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6875, "maximum" : 0.7500 }
},
{
"index" : 55,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7500, "maximum" : 0.8125 }
},
{
"index" : 56,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8125, "maximum" : 0.8750 }
},
{
"index" : 57,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8750, "maximum" : 0.9375 }
},
{
"index" : 58,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.9375, "maximum" : 1.0000 }
},
{
"index" : 59,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0370 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 60,
"hscan" : { "minimum" : 0.0370, "maximum" : 0.0741 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 61,
"hscan" : { "minimum" : 0.0741, "maximum" : 0.1111 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 62,
"hscan" : { "minimum" : 0.1111, "maximum" : 0.1481 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 63,
"hscan" : { "minimum" : 0.1481, "maximum" : 0.1852 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 64,
"hscan" : { "minimum" : 0.1852, "maximum" : 0.2222 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 65,
"hscan" : { "minimum" : 0.2222, "maximum" : 0.2593 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 66,
"hscan" : { "minimum" : 0.2593, "maximum" : 0.2963 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 67,
"hscan" : { "minimum" : 0.2963, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 68,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3704 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 69,
"hscan" : { "minimum" : 0.3704, "maximum" : 0.4074 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 70,
"hscan" : { "minimum" : 0.4074, "maximum" : 0.4444 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 71,
"hscan" : { "minimum" : 0.4444, "maximum" : 0.4815 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 72,
"hscan" : { "minimum" : 0.4815, "maximum" : 0.5185 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 73,
"hscan" : { "minimum" : 0.5185, "maximum" : 0.5556 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 74,
"hscan" : { "minimum" : 0.5556, "maximum" : 0.5926 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 75,
"hscan" : { "minimum" : 0.5926, "maximum" : 0.6296 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 76,
"hscan" : { "minimum" : 0.6296, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 77,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7037 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 78,
"hscan" : { "minimum" : 0.7037, "maximum" : 0.7407 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 79,
"hscan" : { "minimum" : 0.7407, "maximum" : 0.7778 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 80,
"hscan" : { "minimum" : 0.7778, "maximum" : 0.8148 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 81,
"hscan" : { "minimum" : 0.8148, "maximum" : 0.8519 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 82,
"hscan" : { "minimum" : 0.8519, "maximum" : 0.8889 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 83,
"hscan" : { "minimum" : 0.8889, "maximum" : 0.9259 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 84,
"hscan" : { "minimum" : 0.9259, "maximum" : 0.9630 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 85,
"hscan" : { "minimum" : 0.9630, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
}
],
"endOfJson" : "endOfJson"
}
Filme ruckeln, seit Hyperion installiert ist
Warum hast du bei xbmcAddress die LAN-IP drin? wenn du nicht gerade zwei RPI hast gehört da 127.0.0.1 rein 
in deiner zweiten Konfiguration hast du die falschen LEDs konfiguriert.
Hast du beim dem RPI3 eine alte /boot/config.txt wo an der CPU Performance geschraubt wird?
in deiner zweiten Konfiguration hast du die falschen LEDs konfiguriert.
Hast du beim dem RPI3 eine alte /boot/config.txt wo an der CPU Performance geschraubt wird?
Kein Support per PM!
-
nitroburger
- Neuling
- Beiträge:11
- Registriert:21. Apr 2016
Filme ruckeln, seit Hyperion installiert ist
Hab die IP geändert und eine spezielle Config.txt habe ich nicht. Nur den Punkt mit Ambilight ON:
Code: Alles auswählen
################################################################################
# This file is part of OpenELEC - http://www.openelec.tv
# Copyright (C) 2009-2014 Stephan Raue (stephan@openelec.tv)
# Inspired and partly copied from:
# http://youresuchageek.blogspot.fr/2012/09/howto-raspberry-pi-openelec-on.html
#
# OpenELEC is free software: you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation, either version 2 of the License, or
# (at your option) any later version.
#
# OpenELEC is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with OpenELEC. If not, see <http://www.gnu.org/licenses/>.
################################################################################
# Bootloader configuration - config.txt
################################################################################
################################################################################
# Memory (System/GPU configuration )
################################################################################
# default GPU memory split (do not change if you do not know what you are doing)
gpu_mem=128
# SDRAM size based GPU memory split, uncomment and setup to override 'gpu_mem'
gpu_mem_256=112
gpu_mem_512=160
gpu_mem_1024=256
################################################################################
# Overclocking settings
# WARNING: Do not change/enable if you do not know what you are doing!
# The System may become unstable or you can have data corruption or
# you can loose your warranty if you set wrong settings
#
# please read: http://elinux.org/RPi_config.txt#Overclocking_configuration
################################################################################
# Overclock mode settings.
#
# default recommended values are: arm_freq | core_freq | sdram_freq | over_voltage
# no overclocking : 700 | 250 | 400 | 0
# mode 'Modest' : 800 | 300 | 400 | 0
# mode 'Medium' : 900 | 333 | 450 | 2
# mode 'High' : 950 | 450 | 450 | 6
# mode 'Turbo' : 1000 | 500 | 600 | 6
# mode 'Pi2' : 1000 | 500 | 500 | 2
# arm_freq=700
# core_freq=250
# sdram_freq=400
# over_voltage=0
# set to 'force_turbo=1' to disable dynamic overclocking (you can lose your warranty!)
force_turbo=0
# If you have any data corruption using Turbo Mode and overclocking
# try with this setting uncommented
# If this still fails, try to use Medium mode without "over_voltage=2"
# If it ultimately keeps failing, forget about this until it gets fixed
# Use a more conservative mode that will works fine in any cases:
# initial_turbo=30
################################################################################
# Overscan settings
################################################################################
# Make display smaller to stop text spilling off the screen
# see also http://www.raspberrypi.org/phpBB3/viewtopic.php?f=67&t=15700
# overscan_scale=1
# disable_overscan=1
# Adapt overscan values to your needs
# overscan_left=57
# overscan_right=59
# overscan_top=20
# overscan_bottom=20
################################################################################
# various settings see also: http://elinux.org/RPi_config.txt
################################################################################
# Force HDMI even if unplugged or powered off
# hdmi_force_hotplug=1
# Doesn't sent initial active source message.
# Avoids bringing CEC (enabled TV) out of standby and channel switch when
# rebooting.
hdmi_ignore_cec_init=1
################################################################################
# License keys to enable GPU hardware decoding for various codecs
# to obtain keys visit the shop at http://www.raspberrypi.com
################################################################################
# decode_MPG2=0x00000000
# decode_WVC1=0x00000000
# decode_DTS=0x00000000
# decode_DDP=0x00000000
################################################################################
# End of default configuration
# all values below this line were inserted from config.txt.bk (your old config)
# and can be merged with the above values
################################################################################
# Ambilight Modul aktivieren
dtparam=spi=onCode: Alles auswählen
// Automatically generated configuration file for 'Hyperion daemon'
// Generated by: HyperCon (The Hyperion deamon configuration file builder)
// Created with HyperCon V1.01.2 (31.03.2016)
{
/// Device configuration contains the following fields:
/// * 'name' : The user friendly name of the device (only used for display purposes)
/// * 'type' : The type of the device or leds (known types for now are
/// ---------SPI---------, APA102, WS2801, P9813, LPD6803, LPD8806, ---------PWM---------, WS2812b (just RPi1), WS281X (RPi1, RPi2, RPi3), --------OTHER--------, PhilipsHUE, AtmoOrb, PiBlaster, Tinkerforge, UDP, FadeCandy, SEDU, TPM2, USBASP-WS2801, USBASP-WS2812, ------3rd PARTY------, Adalight, AdalightAPA102, AmbiLed, Atmo, Lightpack, Multi-Lightpack, Paintpack, Test (file), None)
/// * [device type specific configuration]
/// * 'colorOrder' : The order of the color bytes ('rgb', 'rbg', 'bgr', etc.).
"device" :
{
"name" : "MyHyperionConfig",
"type" : "ws2801",
"output" : "/dev/spidev0.0",
"rate" : 1000000,
"colorOrder" : "rgb"
},
/// Color manipulation configuration used to tune the output colors to specific surroundings.
/// The configuration contains a list of color-transforms. Each transform contains the
/// following fields:
/// * 'id' : The unique identifier of the color transformation (eg 'device_1') /// * 'leds' : The indices (or index ranges) of the leds to which this color transform applies
/// (eg '0-5, 9, 11, 12-17'). The indices are zero based. /// * 'hsv' : The manipulation in the Hue-Saturation-Value color domain with the following
/// tuning parameters:
/// - 'saturationGain' The gain adjustement of the saturation
/// - 'valueGain' The gain adjustement of the value
/// * 'red'/'green'/'blue' : The manipulation in the Red-Green-Blue color domain with the
/// following tuning parameters for each channel:
/// - 'threshold' The minimum required input value for the channel to be on
/// (else zero)
/// - 'gamma' The gamma-curve correction factor
/// - 'blacklevel' The lowest possible value (when the channel is black)
/// - 'whitelevel' The highest possible value (when the channel is white)
///
/// Next to the list with color transforms there is also a smoothing option.
/// * 'smoothing' : Smoothing of the colors in the time-domain with the following tuning
/// parameters:
/// - 'type' The type of smoothing algorithm ('linear' or 'none')
/// - 'time_ms' The time constant for smoothing algorithm in milliseconds
/// - 'updateFrequency' The update frequency of the leds in Hz
/// - 'updateDelay' The delay of the output to leds (in periods of smoothing)
"color" :
{
"correction" :
[
{
"id" : "default",
"leds" : "*",
"correctionValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"temperature" :
[
{
"id" : "default",
"leds" : "*",
"temperatureValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"transform" :
[
{
"id" : "default",
"leds" : "*",
"hsv" :
{
"saturationGain" : 1.0000,
"valueGain" : 1.0000
},
"hsl" :
{
"saturationGain" : 1.0000,
"luminanceGain" : 1.0000
},
"red" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"green" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
},
"blue" :
{
"threshold" : 0.0000,
"gamma" : 1.0000,
"blacklevel" : 0.0000,
"whitelevel" : 1.0000
}
}
],
"smoothing" :
{
"type" : "linear",
"time_ms" : 100,
"updateFrequency" : 25.0000,
"updateDelay" : 0
}
},
/// The black border configuration, contains the following items:
/// * enable : true if the detector should be activated
/// * threshold : Value below which a pixel is regarded as black (value between 0.0 and 1.0)
/// * unknownFrameCnt : Number of frames without any detection before the border is set to 0 (default 600)
/// * borderFrameCnt : Number of frames before a consistent detected border gets set (default 50)
/// * maxInconsistentCnt : Number of inconsistent frames that are ignored before a new border gets a chance to proof consistency
/// * blurRemoveCnt : Number of pixels that get removed from the detected border to cut away blur (default 1)
/// * mode : Border detection mode (values=default,classic,osd)
"blackborderdetector" :
{
"enable" : true,
"threshold" : 0.01,
"unknownFrameCnt" : 600,
"borderFrameCnt" : 50,
"maxInconsistentCnt" : 10,
"blurRemoveCnt" : 1,
"mode" : "default"
},
/// The configuration of the effect engine, contains the following items:
/// * paths : An array with absolute location(s) of directories with effects
/// * color : Set static color after boot -> set effect to "" (empty) and input the values [R,G,B] and set duration_ms NOT to 0 (use 1) instead
/// * effect : The effect selected as 'boot sequence'
/// * duration_ms : The duration of the selected effect (0=endless)
/// * priority : The priority of the selected effect/static color (default=990) HINT: lower value result in HIGHER priority!
"effects" :
{
"paths" :
[
"/storage/hyperion/effects"
]
},
// "bootsequence" :
// {
// "color" : [0,0,0],
// "effect" : "Rainbow swirl fast",
// "duration_ms" : 3000,
// "priority" : 990
// },
/// The configuration of the Json/Proto forwarder. Forward messages to multiple instances of Hyperion on same and/or other hosts
/// 'proto' is mostly used for video streams and 'json' for effects
/// * proto : Proto server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19447"] or more instances to forward ["127.0.0.1:19447","192.168.0.24:19449"]
/// * json : Json server adress and port of your target. Syntax:[IP:PORT] -> ["127.0.0.1:19446"] or more instances to forward ["127.0.0.1:19446","192.168.0.24:19448"]
/// HINT: If you redirect to "127.0.0.1" (localhost) you could start a second hyperion with another device/led config!
/// Be sure your client(s) is/are listening on the configured ports. The second Hyperion (if used) also needs to be configured! (HyperCon -> External -> Json Server/Proto Server)
// "forwarder" :
// {
// "proto" : ["127.0.0.1:19447"],
// "json" : ["127.0.0.1:19446"]
// },
/// The configuration for the frame-grabber, contains the following items:
/// * width : The width of the grabbed frames [pixels]
/// * height : The height of the grabbed frames [pixels]
/// * frequency_Hz : The frequency of the frame grab [Hz]
/// * priority : The priority of the frame-gabber (Default=890) HINT: lower value result in HIGHER priority!
/// * ATTENTION : Power-of-Two resolution is not supported and leads to unexpected behaviour!
"framegrabber" :
{
"width" : 80,
"height" : 45,
"frequency_Hz" : 10.0,
"priority" : 890
},
/// The configuration of the Kodi connection used to enable and disable the frame-grabber. Contains the following fields:
/// * xbmcAddress : The IP address of the Kodi-host
/// * xbmcTcpPort : The TCP-port of the Kodi-server
/// * grabVideo : Flag indicating that the frame-grabber is on(true) during video playback
/// * grabPictures : Flag indicating that the frame-grabber is on(true) during picture show
/// * grabAudio : Flag indicating that the frame-grabber is on(true) during audio playback
/// * grabMenu : Flag indicating that the frame-grabber is on(true) at the Kodi menu
/// * grabScreensaver : Flag indicating that the frame-grabber is on(true) when Kodi is on screensaver
/// * enable3DDetection : Flag indicating that the frame-grabber should switch to a 3D compatible modus if a 3D video is playing
"xbmcVideoChecker" :
{
"xbmcAddress" : "127.0.0.1",
"xbmcTcpPort" : 9090,
"grabVideo" : true,
"grabPictures" : false,
"grabAudio" : false,
"grabMenu" : false,
"grabScreensaver" : false,
"enable3DDetection" : false
},
/// The configuration of the Json server which enables the json remote interface
/// * port : Port at which the json server is started
"jsonServer" :
{
"port" : 19444
},
/// The configuration of the Proto server which enables the protobuffer remote interface
/// * port : Port at which the protobuffer server is started
"protoServer" :
{
"port" : 19445
},
/// The configuration of the boblight server which enables the boblight remote interface
/// * port : Port at which the boblight server is started
/// * priority: Priority of the boblight server (Default=900) HINT: lower value result in HIGHER priority!
// "boblightServer" :
// {
// "port" : 19333,
// "priority" : 900
// },
/// Configuration for the embedded V4L2 grabber
/// * device : V4L2 Device to use [default="/dev/video0"]
/// * input : V4L2 input to use [default=0]
/// * standard : Video standard (no-change/PAL/NTSC) [default="no-change"]
/// * width : V4L2 width to set [default=-1]
/// * height : V4L2 height to set [default=-1]
/// * frameDecimation : Frame decimation factor [default=2]
/// * sizeDecimation : Size decimation factor [default=8]
/// * priority : Hyperion priority channel [default=900]
/// * mode : 3D mode to use 2D/3DSBS/3DTAB (note: no autodetection) [default="2D"]
/// * cropLeft : Cropping from the left [default=0]
/// * cropRight : Cropping from the right [default=0]
/// * cropTop : Cropping from the top [default=0]
/// * cropBottom : Cropping from the bottom [default=0]
/// * redSignalThreshold : Signal threshold for the red channel between 0.0 and 1.0 [default=0.0]
/// * greenSignalThreshold : Signal threshold for the green channel between 0.0 and 1.0 [default=0.0]
/// * blueSignalThreshold : Signal threshold for the blue channel between 0.0 and 1.0 [default=0.0]
// "grabber-v4l2" :
// {
// "device" : "/dev/video0",
// "input" : 0,
// "standard" : "no-change",
// "width" : -1,
// "height" : -1,
// "frameDecimation" : 2,
// "sizeDecimation" : 8,
// "priority" : 900,
// "mode" : "2D",
// "cropLeft" : 0,
// "cropRight" : 0,
// "cropTop" : 0,
// "cropBottom" : 0,
// "redSignalThreshold" : 0.0,
// "greenSignalThreshold" : 0.0,
// "blueSignalThreshold" : 0.0
// },
/// The configuration for each individual led. This contains the specification of the area
/// averaged of an input image for each led to determine its color. Each item in the list
/// contains the following fields:
/// * index: The index of the led. This determines its location in the string of leds; zero
/// being the first led.
/// * hscan: The fractional part of the image along the horizontal used for the averaging
/// (minimum and maximum inclusive)
/// * vscan: The fractional part of the image along the vertical used for the averaging
/// (minimum and maximum inclusive)
"leds" :
[
{
"index" : 0,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9375, "maximum" : 1.0000 }
},
{
"index" : 1,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8750, "maximum" : 0.9375 }
},
{
"index" : 2,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8125, "maximum" : 0.8750 }
},
{
"index" : 3,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7500, "maximum" : 0.8125 }
},
{
"index" : 4,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6875, "maximum" : 0.7500 }
},
{
"index" : 5,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6250, "maximum" : 0.6875 }
},
{
"index" : 6,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5625, "maximum" : 0.6250 }
},
{
"index" : 7,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5625 }
},
{
"index" : 8,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4375, "maximum" : 0.5000 }
},
{
"index" : 9,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3750, "maximum" : 0.4375 }
},
{
"index" : 10,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3125, "maximum" : 0.3750 }
},
{
"index" : 11,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2500, "maximum" : 0.3125 }
},
{
"index" : 12,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1875, "maximum" : 0.2500 }
},
{
"index" : 13,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1250, "maximum" : 0.1875 }
},
{
"index" : 14,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0625, "maximum" : 0.1250 }
},
{
"index" : 15,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0625 }
},
{
"index" : 16,
"hscan" : { "minimum" : 0.9630, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 17,
"hscan" : { "minimum" : 0.9259, "maximum" : 0.9630 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 18,
"hscan" : { "minimum" : 0.8889, "maximum" : 0.9259 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 19,
"hscan" : { "minimum" : 0.8519, "maximum" : 0.8889 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 20,
"hscan" : { "minimum" : 0.8148, "maximum" : 0.8519 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 21,
"hscan" : { "minimum" : 0.7778, "maximum" : 0.8148 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 22,
"hscan" : { "minimum" : 0.7407, "maximum" : 0.7778 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 23,
"hscan" : { "minimum" : 0.7037, "maximum" : 0.7407 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 24,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7037 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 25,
"hscan" : { "minimum" : 0.6296, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 26,
"hscan" : { "minimum" : 0.5926, "maximum" : 0.6296 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 27,
"hscan" : { "minimum" : 0.5556, "maximum" : 0.5926 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 28,
"hscan" : { "minimum" : 0.5185, "maximum" : 0.5556 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 29,
"hscan" : { "minimum" : 0.4815, "maximum" : 0.5185 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 30,
"hscan" : { "minimum" : 0.4444, "maximum" : 0.4815 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 31,
"hscan" : { "minimum" : 0.4074, "maximum" : 0.4444 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 32,
"hscan" : { "minimum" : 0.3704, "maximum" : 0.4074 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 33,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3704 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 34,
"hscan" : { "minimum" : 0.2963, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 35,
"hscan" : { "minimum" : 0.2593, "maximum" : 0.2963 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 36,
"hscan" : { "minimum" : 0.2222, "maximum" : 0.2593 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 37,
"hscan" : { "minimum" : 0.1852, "maximum" : 0.2222 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 38,
"hscan" : { "minimum" : 0.1481, "maximum" : 0.1852 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 39,
"hscan" : { "minimum" : 0.1111, "maximum" : 0.1481 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 40,
"hscan" : { "minimum" : 0.0741, "maximum" : 0.1111 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 41,
"hscan" : { "minimum" : 0.0370, "maximum" : 0.0741 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 42,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0370 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 43,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0625 }
},
{
"index" : 44,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0625, "maximum" : 0.1250 }
},
{
"index" : 45,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1250, "maximum" : 0.1875 }
},
{
"index" : 46,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1875, "maximum" : 0.2500 }
},
{
"index" : 47,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2500, "maximum" : 0.3125 }
},
{
"index" : 48,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3125, "maximum" : 0.3750 }
},
{
"index" : 49,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3750, "maximum" : 0.4375 }
},
{
"index" : 50,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4375, "maximum" : 0.5000 }
},
{
"index" : 51,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5000, "maximum" : 0.5625 }
},
{
"index" : 52,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5625, "maximum" : 0.6250 }
},
{
"index" : 53,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6250, "maximum" : 0.6875 }
},
{
"index" : 54,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6875, "maximum" : 0.7500 }
},
{
"index" : 55,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7500, "maximum" : 0.8125 }
},
{
"index" : 56,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8125, "maximum" : 0.8750 }
},
{
"index" : 57,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8750, "maximum" : 0.9375 }
},
{
"index" : 58,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.9375, "maximum" : 1.0000 }
},
{
"index" : 59,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0370 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 60,
"hscan" : { "minimum" : 0.0370, "maximum" : 0.0741 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 61,
"hscan" : { "minimum" : 0.0741, "maximum" : 0.1111 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 62,
"hscan" : { "minimum" : 0.1111, "maximum" : 0.1481 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 63,
"hscan" : { "minimum" : 0.1481, "maximum" : 0.1852 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 64,
"hscan" : { "minimum" : 0.1852, "maximum" : 0.2222 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 65,
"hscan" : { "minimum" : 0.2222, "maximum" : 0.2593 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 66,
"hscan" : { "minimum" : 0.2593, "maximum" : 0.2963 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 67,
"hscan" : { "minimum" : 0.2963, "maximum" : 0.3333 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 68,
"hscan" : { "minimum" : 0.3333, "maximum" : 0.3704 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 69,
"hscan" : { "minimum" : 0.3704, "maximum" : 0.4074 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 70,
"hscan" : { "minimum" : 0.4074, "maximum" : 0.4444 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 71,
"hscan" : { "minimum" : 0.4444, "maximum" : 0.4815 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 72,
"hscan" : { "minimum" : 0.4815, "maximum" : 0.5185 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 73,
"hscan" : { "minimum" : 0.5185, "maximum" : 0.5556 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 74,
"hscan" : { "minimum" : 0.5556, "maximum" : 0.5926 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 75,
"hscan" : { "minimum" : 0.5926, "maximum" : 0.6296 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 76,
"hscan" : { "minimum" : 0.6296, "maximum" : 0.6667 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 77,
"hscan" : { "minimum" : 0.6667, "maximum" : 0.7037 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 78,
"hscan" : { "minimum" : 0.7037, "maximum" : 0.7407 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 79,
"hscan" : { "minimum" : 0.7407, "maximum" : 0.7778 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 80,
"hscan" : { "minimum" : 0.7778, "maximum" : 0.8148 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 81,
"hscan" : { "minimum" : 0.8148, "maximum" : 0.8519 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 82,
"hscan" : { "minimum" : 0.8519, "maximum" : 0.8889 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 83,
"hscan" : { "minimum" : 0.8889, "maximum" : 0.9259 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 84,
"hscan" : { "minimum" : 0.9259, "maximum" : 0.9630 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 85,
"hscan" : { "minimum" : 0.9630, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
}
],
"endOfJson" : "endOfJson"
}
Filme ruckeln, seit Hyperion installiert ist
Servus,
habe ein ähnliches Problem. Hab das System jetzt schon des öfteren komplett neu auf die SD-Karte installiert.
Der letzte Versuch brachte 3h Erfolg, Bild schön, Ton schön, Ambilight herrlich. Dann nächste Episode gestartet...Ambilight immer noch herrlich, Bild sehr oft weg und manchmal sogar HDMI-Signal (Ambilight funtkioniert aber weiterhin), Ton auch ab und zu weg.
Ich schreib euch heut Abend mal meine Hyperioncfg usw.
Ich wollt als nächstes das Netzteil+ Kabel vom Raspi tauschen(bisher 5V,1,7A). Um Stromschwankungen auszuschließen
habe ein ähnliches Problem. Hab das System jetzt schon des öfteren komplett neu auf die SD-Karte installiert.
Der letzte Versuch brachte 3h Erfolg, Bild schön, Ton schön, Ambilight herrlich. Dann nächste Episode gestartet...Ambilight immer noch herrlich, Bild sehr oft weg und manchmal sogar HDMI-Signal (Ambilight funtkioniert aber weiterhin), Ton auch ab und zu weg.
Ich schreib euch heut Abend mal meine Hyperioncfg usw.
Ich wollt als nächstes das Netzteil+ Kabel vom Raspi tauschen(bisher 5V,1,7A). Um Stromschwankungen auszuschließen